Malaguti Dune X 125 страница 92 Скачать руководство пользователя

Страница: 92 / 272

Dune 125 - Dune X 125 - Euro 4

Electrical system

ELE SYS - 92



Verify continuity of the wiring harness between the sensor connector and the control unit

connector: control unit PIN 31 - sensor PIN B. If necessary, restore the wiring harness.



Verify continuity of the wiring harness between the sensor connector and the injection relay:

sensor PIN A - injection relay PIN 3. If necessary, restore the wiring harness.



If the wiring harness is intact and the error persists, proceed with the following checks.

Short circuit to negative:



Disconnect the sensor connector.



Check the sensor connector PIN B ground insulation. If there is no insulation, restore the

wiring harness.



If PIN B is insulated from ground and in the absence of other errors (fuel pump, injector,

coil), this means that the control unit is most likely faulty.

Injector

Function

Provide the correct amount of fuel at the correct time.

Operation / Operating principle

Injector coil is excited for the petrol passage to open.

Level in electrical circuit diagram

Relay for injection utilities, Coils and injectors

Electrical specifications



14.8 Ώ +/- 5% (at 20 °C - 68°F)

Pin-out:

1. Control unit ground

2. Power via relay

Diagnostic tool - Activation



Injector control

Diagnostic tool - Electrical errors

Injector P0201 -

short circuit to positive / short cir-

cuit to negative / open circuit.

Error cause

Short-circuit to positive: excessive voltage to PIN

34 of the control unit connector.

Short circuit to negative: zero voltage to the PIN 2

of the injector connector.

Open circuit: circuit interruption.

Troubleshooting

Содержание Dune X 125

















































































































































































































































































Результаты поиска

Содержание Dune X 125

Отзывы:

Похожие инструкции для Dune X 125

Бренды по названию

Популярные бренды

Malaguti Dune X 125, Руководство по обслуживанию станции

Результаты поиска

Содержание Dune X 125

Отзывы:

Похожие инструкции для Dune X 125

Бренды по названию

Популярные бренды