manualshive.com logo in svg

Malaguti Dune X 125, Руководство по обслуживанию станции, Страница: 234 / 272

Поделиться
Скачать
Malaguti Dune X 125 Скачать руководство пользователя страница 234

Dune 125 - Dune X 125 - Euro 4

Braking system

BRAK SYS - 234

If runout exceeds the service limit, replace the disc.

Disc Runout

Standard: TIR 0.15 mm (0.0059 in.) or less

Service Limit: TIR 0.3 mm (0.01 in.)

Brake Fluid

Brake Fluid Level Inspection

Refer to the Brake Fluid Level Inspection in the Periodic Maintenance chapter.

Brake Fluid Change

Refer to the Brake Fluid Change in the Periodic Maintenance chapter.

Brake Line Bleeding

The brake fluid has a very low compression coefficient so that almost all the movement of the brake

lever or pedal is transmitted directly to the caliper for braking action. Air, however, is easily

compressed. When air enters the brake lines, brake lever or pedal movement will be partially used in

compressing the air. This will make the lever or pedal feel spongy, and there will be a loss in braking

power.

BE SURE TO BLEED THE AIR FROM THE BRAKE LINE WHENEVER BRAKE LEVER OR
PEDAL ACTION FEELS SOFT OR SPONGY AFTER THE BRAKE FLUID IS CHANGE, OR
WHENEVER A BRAKE LINE FITTING HAS BEEN LOOSENED FOR ANY REASON.

NOTE

THE PROCEDURE YO BLEED THE FRONT BRAKE LINE IS AS FOLLOWS. BLEEDING THE
REAR BRAKE LINE IS THE SAME AS FOR THE FRONT BRAKE.

Remove the reservoir cap [A] and

diaphragm.

Fill the reservoir with fresh brake fluid

to the upper level line in the reservoir.

Slowly pump the brake lever several

times until no air bubbles can be seen rising up

through the fluid from the holes at the bottom of

the reservoir.

Bleed the air completely from the master

cylinder by this operation.

Remove the rubber cap from the

bleed valve [A] on the caliper.

Attach a clear plastic hose to the

bleed valve[B], and run the other end of the hose

into a container.

Содержание Dune X 125

















































































































































































































































































Отзывы:

Нет отзывов