Makita BHP454 Скачать руководство пользователя

Страница: 8 / 60

grip and switch handle during operations. Failure to do
so may result in the loss of control of the tool and
potentially severe injury.

First, slide the action mode change lever so that it points
to the

marking. The adjusting ring can be aligned in any

torque levels for this operation. Be sure to use a tungsten-
carbide tipped bit. Position the bit at the desired location
for the hole, then pull the switch trigger. Do not force the
tool. Light pressure gives best results. Keep the tool in
position and prevent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.

Blow-out bulb (optional accessory)
(Fig. 15)

After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.

Screwdriving operation

First, slide the action mode change lever so that it points
to the

marking. Adjust the adjusting ring to the proper

torque level for your work. Then proceed as follows.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.

NOTE:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

• When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece.
See the chart.

NOTE:

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.

Drilling operation

CAUTION:

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve
to damage the tip of your bit, decrease the tool
performance and shorten the service life of the tool.

• There is a tremendous force exerted on the tool/bit at

the time of hole break through. Hold the tool firmly and

exert care when the bit begins to break through the
workpiece.

• A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you do
not hold it firmly.

• Always secure small workpieces in a vise or similar

hold-down device.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.

First, slide the action mode change lever so that it points
to the

marking. The adjusting ring can be aligned in any

torque levels for this operation. Then proceed as follows.

Drilling in wood

When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the bit into the workpiece.

Drilling in metal

To prevent the bit from slipping when starting a hole,
make an indentation with a center-punch and hammer at
the point to be drilled. Place the point of the bit in the
indentation and start drilling. Use a cutting lubricant when
drilling metals. The exceptions are iron and brass which
should be drilled dry.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to
perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 16)

Replace when they wear down to the limit mark. Keep the
carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove two screws then remove the
rear cover.

(Fig. 17)

Raise the arm part of the spring and then place it in the
recessed part of the housing with a slotted bit screwdriver
of slender shaft or the like.

(Fig. 18)

Use pliers to remove the carbon brush caps of the carbon
brushes. Take out the worn carbon brushes, insert the
new ones and replace the carbon brush caps in reverse.

(Fig. 19)

Make sure that the carbon brush caps have fit into the
holes in brush holders securely.

(Fig. 20)

Reinstall the rear cover and tighten two screws securely.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might

Nominal diameter of wood

screw (mm)

Recommended size of pilot

hole (mm)

3.1

2.0 - 2.2

3.5

2.2 - 2.5