Major 1150 Slurry Vac Скачать руководство пользователя страница 40

Страница: 40 / 89

www.major-equipment.com

Inspecting the Blades

To check the state of wear of the blades in the Rotary blades vacuum pump

proceed as follows:

•

Remove the threaded inspection plug;

•

Rotate the rotor until a blades lines up with the inspection hole;

•

Compare the height of the blades with the reference ring on the rotor;

•

Replace the entire set of blades when the height is less than the

reference ring on the rotor.

Replacing the Blades

Check that there is sufficient space at the back of the Rotary blades vacuum pump to be able to work easily; if

there is not, the Rotary blades vacuum pump should be taken off its support beforehand;

2. Remove the back

3. Extract the blades from the rotor;

4. Replace the blades;

5. Clean the Rotary blades vacuum pump.

Re-fit the back of the Rotary blades vacuum pump

7. Use original spare parts only

Blade Sizes

Содержание 1150 Slurry Vac


























































































Результаты поиска

Содержание 1150 Slurry Vac

Отзывы:

Похожие инструкции для 1150 Slurry Vac

Бренды по названию

Популярные бренды

Major 1150 Slurry Vac, Руководство оператора и список запчастей

Результаты поиска

Содержание 1150 Slurry Vac

Отзывы:

Похожие инструкции для 1150 Slurry Vac

Бренды по названию

Популярные бренды