Major 1150 Slurry Vac Скачать руководство пользователя страница 20

Страница: 20 / 89

www.major-equipment.com

CHOPPER BLADE DETAIL.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS
REMOVE HOUSING (G88) FIRST

REMOVE CHOPPPER BLADE AS SHOWN
REMOVE HEX NUT (G37)
CHOPPER BLADE (G89) PULLS OFF KEYED SHAFT.(G92)

REMOVE OUTER HOUSING(G91) TO GAIN ACCESS TO COUNTERSUNK
BOLTS TO REMOVE COUNTER BLADES (G90)

NOTE:

BLADE GAP OF 2.5-3MM WHEN ASSEMBLED.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS &

REMOVE CHOPPPER BLADE AS SHOWN

PULLS OFF KEYED SHAFT.(G92)

(G91) TO GAIN ACCESS TO COUNTERSUNK

BOLTS TO REMOVE COUNTER BLADES (G90)

WHEN ASSEMBLED.

CHOPPER BLADE DETAIL.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS
REMOVE HOUSING (G88) FIRST

REMOVE CHOPPPER BLADE AS SHOWN
REMOVE HEX NUT (G37)
CHOPPER BLADE (G89) PULLS OFF KEYED SHAFT.(G92)

REMOVE OUTER HOUSING(G91) TO GAIN ACCESS TO COUNTERSUNK
BOLTS TO REMOVE COUNTER BLADES (G90)

NOTE:

BLADE GAP OF 2.5-3MM WHEN ASSEMBLED.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS &

REMOVE CHOPPPER BLADE AS SHOWN

PULLS OFF KEYED SHAFT.(G92)

(G91) TO GAIN ACCESS TO COUNTERSUNK

BOLTS TO REMOVE COUNTER BLADES (G90)

WHEN ASSEMBLED.

CHOPPER BLADE DETAIL.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS
REMOVE HOUSING (G88) FIRST

REMOVE CHOPPPER BLADE AS SHOWN
REMOVE HEX NUT (G37)
CHOPPER BLADE (G89) PULLS OFF KEYED SHAFT.(G92)

REMOVE OUTER HOUSING(G91) TO GAIN ACCESS TO COUNTERSUNK
BOLTS TO REMOVE COUNTER BLADES (G90)

NOTE:

BLADE GAP OF 2.5-3MM WHEN ASSEMBLED.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS &

REMOVE CHOPPPER BLADE AS SHOWN

PULLS OFF KEYED SHAFT.(G92)

(G91) TO GAIN ACCESS TO COUNTERSUNK

BOLTS TO REMOVE COUNTER BLADES (G90)

WHEN ASSEMBLED.

CHOPPER BLADE DETAIL.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS
REMOVE HOUSING (G88) FIRST

REMOVE CHOPPPER BLADE AS SHOWN
REMOVE HEX NUT (G37)
CHOPPER BLADE (G89) PULLS OFF KEYED SHAFT.(G92)

REMOVE OUTER HOUSING(G91) TO GAIN ACCESS TO COUNTERSUNK
BOLTS TO REMOVE COUNTER BLADES (G90)

NOTE:

BLADE GAP OF 2.5-3MM WHEN ASSEMBLED.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS &

REMOVE CHOPPPER BLADE AS SHOWN

PULLS OFF KEYED SHAFT.(G92)

(G91) TO GAIN ACCESS TO COUNTERSUNK

BOLTS TO REMOVE COUNTER BLADES (G90)

WHEN ASSEMBLED.

CHOPPER BLADE DETAIL.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS
REMOVE HOUSING (G88) FIRST

REMOVE CHOPPPER BLADE AS SHOWN
REMOVE HEX NUT (G37)
CHOPPER BLADE (G89) PULLS OFF KEYED SHAFT.(G92)

REMOVE OUTER HOUSING(G91) TO GAIN ACCESS TO COUNTERSUNK
BOLTS TO REMOVE COUNTER BLADES (G90)

NOTE:

BLADE GAP OF 2.5-3MM WHEN ASSEMBLED.

TO ACCESS CHOPPER BLADE REMOVE INNER RING OF BOLTS &

REMOVE CHOPPPER BLADE AS SHOWN

PULLS OFF KEYED SHAFT.(G92)

(G91) TO GAIN ACCESS TO COUNTERSUNK

BOLTS TO REMOVE COUNTER BLADES (G90)

WHEN ASSEMBLED.

To fill tank.

1. Turn gear lever towards the left to select the vacuum pump.

2. Turn the handle of the Vacuum pump towards the left to select the Vacuum stage.

3. Activate tractor PTO.

To Empty tank. (i.e. spreading slurry)

1. Turn gear lever towards the left to select the vacuum pump.

2. Turn the gear lever towards the right to select the pressure stage.

3. Activate tractor PTO.

To Operate Jetter / Road Blaster.

1. Turn the gear lever of the) towards the right to select the centrifugal pump.

2. Put the handle of the vacuum pump (A) to the neutral (Centre) position. This ensures that unwanted decompression

is not experienced by the tanker.

Centrifugal pump

Operating time: Maximum advisable working time should not exceed 30 minutes to avoid overheating the gearbox.

Pressure: Operating pressure should be kept at approx. 5 bar to avoid overheating of the centrifugal pump. However

never exceed a pressure of 6 bar.

Absorbed Power: It is necessary to operate the garda pump with a power of approx. 70 kW (94hp). Never apply greater

power than 80 kW (107hp) to the PTO to avoid damaging the gearbox.

In frosty weather the centrifugal pump and slurry hoses must be drained of all liquids to avoid damage to the

equipment.

Chopper Blade Detail

To access the chopper

blade, remove inner ring of

bolts and remove housing

(G88) first

Remove the chopper blade

as shown. Remove hex

nut (G37). The chopper

blade (G89) pulls of the

keyed shaft (G92)

Remove outer housing

(G91) to gain access to

countersunk bolts to re-

move couter blades (G90)

Note: The blade gap of 2.5

- 3mm when assembled

Содержание 1150 Slurry Vac


























































































Результаты поиска

Содержание 1150 Slurry Vac

Отзывы:

Похожие инструкции для 1150 Slurry Vac

Бренды по названию

Популярные бренды

Major 1150 Slurry Vac, Руководство оператора и список запчастей

Результаты поиска

Содержание 1150 Slurry Vac

Отзывы:

Похожие инструкции для 1150 Slurry Vac

Бренды по названию

Популярные бренды