Major 1150 Slurry Vac Скачать руководство пользователя страница 21

Страница: 21 / 89

www.major-equipment.com

Cyclone Trap

Do not attempt to open cyclone trap when pressurised

Check for sediment periodically by opening the drainage cock located

underneath the Cyclone

Operation of the Rain Gun

Follow the following instructions carefully.

1. Connect the two hydraulic hoses for the rain gun to a double-acting valve on the tractor and check that it rotates

through 360 degrees.

2. Engage centrifugal pump and change lever on the vacuum pump to its neutral position (Refer to section “To empty

tank” on the previous page).

3. Operate Stone Trap Gate Valve to allow slurry into Garda pump

4. The rain gun spreading direction can be rotated to a desired direction by double acting valve on the tractor.

A stone trap is fitted on the bottom of the tank; this is to be cleaned out regularly during the working day.

6. PTO speed maximum is 540 R.P.M.

Operation of the Road Blaster

A clean water source is vital for the

Road Blaster to function correctly.

Follow the following instructions carefully.

1. Connect the two hydraulic hoses for the

Road Blaster lift ram to a double-acting valve

on the tractor and check that it lifts & lowers

the blaster bar.

2. Adjust the angle of the Blaster to wash either

to the left or right & lock in position.

3. Engage PTO & open stone trap gate valve.

4. For the differing conditions, vary forward speed

& tractor RPM to find optimum cleaning ability.

Periodically check stone trap filter. Stone trap

filter is held in place by a 4” BSP thread.

Содержание 1150 Slurry Vac


























































































Результаты поиска

Содержание 1150 Slurry Vac

Отзывы:

Похожие инструкции для 1150 Slurry Vac

Бренды по названию

Популярные бренды

Major 1150 Slurry Vac, Руководство оператора и список запчастей

Результаты поиска

Содержание 1150 Slurry Vac

Отзывы:

Похожие инструкции для 1150 Slurry Vac

Бренды по названию

Популярные бренды