Majestic SA42R страница 6 Скачать руководство пользователя

Страница: 6 / 40

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

Across a

corner

As a

room

divider

48 in.

(1219 mm)

minimum

Along a wall

1/2 in. (13 mm) all

configurations

3/4 in. (19 mm) min. air

space from fireplace to

combustible materials. 1/2

in. (13 mm) allowed at

nailing flanges.

Note:

In an exterior chase

or projecting into a

garage

Note:

Measurements are FRAMING dimensions only and do

not include drywall either in the cavity or on the interior walls.

8 in. (203 mm) extra space

included for outside air

connection. If outside air duct

has no bend, this dimension

may be reduced as long as

minimum clearances are met.

Model #

in.

74 7/8

35 3/4

15 3/4

1295

1092

1902

908

400

1346

584

in.

77 1/2

38 7/8

54 7/8

1448

1245

1969

987

457

1394

584

SA36

SA42

12 in. (305 mm)

Minimum from FP

opening to any

perpendicular wall.

Figure 2.2 Fireplace Locations

NOTICE:

• Illustrations and photos reflect typical installations and

are FOR DESIGN PURPOSES ONLY.

• Illustrations/diagrams are not drawn to scale.

• Actual installation/appearance may vary due to individual

design preference.

• Vermont Casting Group reserves the right to alter its

products.

NOTICE:

In addition to these framing dimensions, also

reference the following section: Clearances (Section 3).

NOTICE:

A minimum 3/4 in. (19 mm) air clearance at the

back and sides of the fireplace assembly must be

maintained.

Chimney sections at any level require

a 2 in. minimum air space clearance

between the framing and chimney sec-

tions.

B. Design and Installation Considerations

NOTICE:

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building inspector, fire

officials or authorities having jurisdiction over restrictions,

installation inspection and permits.

•

Before installing

, determine the following:

- Where the fireplace is to be installed.

- The vent system configuration to be used.

- Gas supply piping.

- Electrical wiring

- Framing and finishing details.

- Whether optional accessories - devices such as a

fan, wall switch or remote control - are desired.

1. Selecting Fireplace Locations

This fireplace may be used as a room divider, installed

along a wall, across a corner or used in an exterior chase.

See Figure 2.2.
Locating the fireplace in a basement should be avoided.

Locating near frequently opened doors, central heat outlets

or returns, or other locations of considerable air movement

can affect the performance.

Consideration should be given to these factors before

deciding on a location.

Содержание SA42R









































Результаты поиска

Содержание SA42R

Отзывы:

Похожие инструкции для SA42R

Бренды по названию

Популярные бренды

Majestic SA42R, Руководство по установке

Результаты поиска

Содержание SA42R

Отзывы:

Похожие инструкции для SA42R

Бренды по названию

Популярные бренды