Majestic SA42R страница 15 Скачать руководство пользователя

Страница: 15 / 40

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

6 ft (1.83 m) max.

unsupported chimney

above roof

20 ft (6.10 m) max.

pipe between an

offset & return

35 ft (10.7 m)

max. straight

unsupported

chimney height

16.5 ft (5.03 m) min. height/single offset-return

20 ft. (6.10 m) min. height/double offset-return

90 ft (27.4 m) max. height

41-3/8 in.

(1051 mm)

Effective

Height

Ceiling firestop

Figure 4.1 Chimney Requirements

NOTICE:

A maximum of two pairs of offsets and returns

may be used.

Minimum overall straight height

16.5 ft

5.03 m

Minimum height with single offset/

return

16.5 ft 45.03 m

Double offset/return minimum height

20 ft

6.1 m

Maximum height

90 ft

27.43 m

Maximum chimney length between an

offset and return

20 ft

6.1 m

Maximum distance between chimney

stabilizers

35 ft

10.67 m

Maximum unsupported chimney

length between the offset and return

6 ft

1.83 m

Maximum unsupported chimney

height above the fireplace

35 ft

10.67 m

Maximum unsupported chimney

above roof

6 ft

1.83 m

WARNING! Risk of Fire!

You must maintain 2

in. (51 mm) air space clearance to insulation

and other combustible materials around the

chimney system. Failure to do so may cause

overheating and fire.

NOTICE

You must provide support for the pipe during

construction and check to be sure inadvertent loading has

not dislodged the chimney section from the fireplace or at

any chimney joint.

A. Chimney Requirements

Vertical distances are measured from the base of the

fireplace as shown in Figure 4.1.

Chimney and Termination Requirements

Table 4.2 Chimney Component Dimensions

Table 4.1 Chimney Requirements

HEIGHT OF CHIMNEY COMPONENTS

in.

Chimney Stabilizer

SL3

4-3/4

121

Offsets/Returns

SL315

13-3/8

340

SL330

15-1/2

394

Chimney Sections*

SL306

4-3/4

121

SL312

10-3/4

273

SL318

16-3/4

425

SL324

22-3/4

578

SL336

34-3/4

883

SL348

46-3/4

1187

* Dimensions reflect effective height.

Содержание SA42R









































Результаты поиска

Содержание SA42R

Отзывы:

Похожие инструкции для SA42R

Бренды по названию

Популярные бренды

Majestic SA42R, Руководство по установке

Результаты поиска

Содержание SA42R

Отзывы:

Похожие инструкции для SA42R

Бренды по названию

Популярные бренды