Majestic SA42R страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 40

background image

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

22

Figure 5.8 Ceiling/Attic Construction

Install Flashing

• Assemble chimney so it passes through the framed

opening.

• Slip the flashing over the chimney.

NOTICE:

Roofing shingles must be below the flashing

plate on the lower side of a sloped roof and over the

flashing plate on the sides and top.

• Nail the flashing to the roof. Keep gaps between the

flashing plate and the roof to a minimum.

• Caulk the flashing plate and roof junction as well as

the vertical seam on the flashing. All nail heads must

be caulked with a roofing sealant.

• Caulk the overlap seam of any exposed pipe sections

that are located above the roof line to prevent leaks.

Slope Downward

(1/4 in. per foot

minimum)

Turn-down

Drip Edge

Chase

2 in. (51 mm) Collar

on Chase Top

.018 (26 ga) min.

Galvanized

Chase Top

Figure 5.9 Chase Top Construction

G. Install Chase/Chase Top

• You MUST use a chase top in a chase installation.

Chase tops may be field constructed.

• Include a turndown and drip edge to prevent water

from seeping into the chase.

• Include a 2 in. (51 mm) soldered, welded or spun

collar around pipe opening to keep water out.

• Provide a 1/8 in. (3 mm) gap around the flue pipe.

• Slope the chase top downward away from the

opening.

WARNING!

Risk of Fire! DO NOT

caulk the pipe to the

chase top collar.

• Caulk all seams to prevent leaks.

F. Roof Penetration

• Refer to Figure 5.8.

• Plumb from roof to center of chimney.

• Drive a nail up through roof to mark center of pipe.

• Measure to either side of nail and mark the 14-1/2 in. x

14-1/2 in. (368 mm x 368 mm) opening required.

• Measure opening on the horizontal; actual length may

be larger depending on roof pitch.

• Cut out and frame opening.

«
...
20
21
22
23
24
...
»

Содержание SA42R









































Отзывы:

Нет отзывов

Похожие инструкции для SA42R

Бренд: GBT Страницы: 18

PALERMO L FTA90546

Бренд: MWH Страницы: 54

Бренд: Real Flame Страницы: 19

Бренд: California Outdoor Concepts Страницы: 8

Sovereign Series

Бренд: Majestic Страницы: 24

Majestic SB5400SS

Бренд: Majestic Страницы: 36

34 Zircon Direct Vent

Бренд: Malm Fireplaces Страницы: 58

Бренд: BOND MANUFACTURING Страницы: 22

attika 600 MAX-1

Бренд: RAIS Страницы: 26

Бренд: Valor Страницы: 12

Бренд: Jøtul Страницы: 12

Бренд: Mosaic Страницы: 17

Leveling Leg Field Fix Kit MPE-27

Бренд: Lennox Hearth Products Страницы: 1

FPB-25SFBS22MT-N

Бренд: Firegear Страницы: 22

Бренд: Somogyi Elektronic Страницы: 20

Бренд: Riello Burners Страницы: 72

Бренд: Nibe Страницы: 48

Бренд: Nibe Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды