Majestic SA42R страница 25 Скачать руководство пользователя

Страница: 25 / 40

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

Shrouds

3 in. (76 mm) tall legs

Ø 17 1/2 in. (444.5 mm), centered round hole to fit over cap

Length x Width to fit inside shroud. Gap not

to exceed 1/2” of shroud base dimension.

*Ensure the shield

does not sag.

Figure 6.1 Radiation Shield

WARNING! Risk of Fire!

Shrouds must be constructed

as specified. Improper construction may overheat

chase top.

NOTICE:

Some regional codes require an agency-Listed

shroud. Consult your local building officials.

Shrouds may be field constructed where permitted by

regional building codes.

The shrouds must be constructed from minimum .018

in. (26 ga) thick aluminized steel.
Some shrouds require a radiation shield. Use where

specified.

A. Radiation Shield

Radiation shield must be constructed of minimum 26 ga

thick sheet metal.

B. Field Constructed Shrouds

The following field constructed shroud designs have

been tested for HHT fireplace systems and termination

caps.

3 in (76 mm)

minimum

Min.

Base Dim.

Min.

Base Dim.

Min.

Top Dim.

Min.

Top Dim.

Min. Opening

Width

Min. Opening

Width

Radiation

Shield

14 1/2 in. (368 mm)

maximum height

TS345

TR344

TR342B

TR342B/TR344

with TR-TVK

Min. Base Dims.

23 x 23

28 x 28

26 x 26

584 x 584

711 x 711

660 x 660

Radiation Shield

Required

Radiation

Shield Not

Required

Min. Top Dims.

20 x 20

25 x 25

23 x 23

508 x 508

635 x 635

584 x 584

Min. Opening Width

17 x 17

22 x 22

20 x 20

432 x 432

559 x 559

508 x 508

1. Open Top Shroud

(TR342/344 TV (top vent) caps do not require radiation

shield)

TR342/344 caps require radiation shield unless installed

partially above the shroud. The TR cap must be raised to

the minimum dimensions (or greater) above the shroud

or install a TR-TVK. Refer to Figure 6.3.

6" Min.

Above the

Shroud.

Storm

Collar

Shroud

Leg

(SHROUD)

(TR Series)

Flue

Shroud

Leg

3 in (76 mm)

air space from

bottom of shroud

to top of chase.

Maximum Height

14 1/2 in. (368 mm)

Chase Top

Figure 6.3 Shroud & TR Series cap with no Radiation Shield

Содержание SA42R









































Результаты поиска

Содержание SA42R

Отзывы:

Похожие инструкции для SA42R

Бренды по названию

Популярные бренды

Majestic SA42R, Руководство по установке

Результаты поиска

Содержание SA42R

Отзывы:

Похожие инструкции для SA42R

Бренды по названию

Популярные бренды