manualshive.com logo in svg

Majestic SA42R, Руководство по установке, Страница: 32 / 40

Поделиться
Скачать
Majestic SA42R Скачать руководство пользователя страница 32

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

32

D. Mantel and Wall Projections

The combustible mantel  may have  a maximum  depth  of 

12  in.  (305  mm),  positioned  12  in.  (305  mm)  above  the 

fireplace opening.  Combustible trim pieces that project no 

more than 1-1/2 in. (38 mm) from the face of the fireplace 

can be placed no closer than 6 in. (152 mm) from the top 

of the fireplace opening. Combustible trim must not cover:

•  the metal surfaces of the fireplace

•  where  the  non-combustible  board  is  placed  over  the 

metal surfaces

•  the space between the metal face of the fireplace and 

framing members

Mantel

6 ft (1829 mm)

minimum

base of fireplace

to ceiling

Combustible Wall

2 x 4 stud wall
Standoffs

Measured from top 

of fireplace opening

12 in./305 mm

1 1/2 in./38 mm

maximum

12 in./305 mm

minimum

6 in./152 mm

minimum

Seal joint with

300° sealant

Non-combustible

Decorative Facing

such as:

Steel, iron, brick,

tile, concrete, slate,

glass, plasters. DO 

NOT cover any air 

openings in the face 

of the fireplace.

43-1/2 in.

1105 mm

minimum 

37-1/2 in.

953 mm

minimum

Base of fireplace

WARNING:

Seal joint with non-combustible

sealant to prevent heat from being

drawn into the wall cavity.

Grid represents 1 in. squares

Figure 7.12  Mantel Specifications

WARNING! Risk of Fire! 

•  You must seal around the finishing material to fireplace.

►

Содержание SA42R









































Отзывы:

Нет отзывов