Majestic SA42R страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 40

background image

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

19

NOTICE:

Chimney sections cannot be disassembled once

locked together. Plan ahead!

• Lock chimney sections and/or offsets/returns together by

pushing downward until the top section meets the stop

bead on the lower section.

• Pull on the top section to make sure it is fully engaged

and will not separate.

• You may use #6 or #8 sheet metal screws no longer than

1/2 in. (13 mm) to fasten chimney sections together. Do

NOT penetrate inner flue.

WARNING!

Risk of Fire!

You MUST use screws to

fasten offset/returns to chimney sections to keep the

chimney parts from twisting. Failure to do so could

cause fire.

• Fasten offset/returns to chimney sections. Do NOT

penetrate inner flue.

• Secure chimney returns with hanger straps provided;

fasten to studs or joists.

• Vertical straight runs of chimney must be supported every

35 ft (10.7 m).

B. Assemble Chimney Sections

Use only those components described in this manual.
Substitute or damaged chimney components could impair

safe operation and cause overheating and fire.
Attach either a straight chimney section or an offset to

the top of the fireplace (depending on your installation

requirement). Chimney sections are locked together by

pushing downward until the top section meets the stop

bead on the lower section.
The inner flue is placed to the inside of the flue section

below it. The outer casing is placed outside the outer cas

-

ing of the chimney section below it. See Figure 5.2.

WARNING! Risk of Fire! DO NOT

install substitute or

damaged chimney components.

Figure 5.2 Assembling Chimney Sections

«
...
17
18
19
20
21
...
»

Содержание SA42R









































Отзывы:

Нет отзывов

Похожие инструкции для SA42R

Home VERSANORA VNF-00115

Бренд: Teamson Страницы: 21

Бренд: Empire Comfort Systems Страницы: 28

Бренд: HOMEDEPOT Страницы: 4

Бренд: Heat & Glo Страницы: 36

Бренд: Valor Страницы: 64

Бренд: Magnum Страницы: 20

Бренд: HWAM Страницы: 52

Бренд: ADURO Страницы: 99

Бренд: Coleman Страницы: 2

Бренд: GlammFire Страницы: 8

Fiery Rock OFG147NG

Бренд: ELEMENTI Страницы: 20

Weyland Round Aluminum

Бренд: Fire Sense Страницы: 18

Бренд: Panadero Страницы: 32

Бренд: Lifepro Страницы: 15

Biochimenea Pur Line Selene

Бренд: climacity Страницы: 4

Бренд: Coitech Страницы: 5

FOCUS HE SLIMLINE SC

Бренд: Paragon Страницы: 28

Бренд: Broadys Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды