Majestic SA42R страница 2 Скачать руководство пользователя

Страница: 2 / 40

Majestic Sovereign Series • SA36R/SA42R • Installers Manual • 4010-259 • Rev K • 1/22

Safety Alert Key:

•

DANGER!

Indicates a hazardous situation which, if not avoided

will result in death or serious injury.

•

WARNING!

Indicates a hazardous situation which, if not avoided could

result in death or serious injury.

•

CAUTION!

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

•

NOTICE:

Indicates practices which may cause damage to the fireplace or to property.

Table of Contents

1 Product Specific & Important Safety Information

A. Fireplace Certification

B. Non-Combustible Materials

C. Combustible Materials

2 Getting Started

A. Typical Fireplace System

B. Design and Installation Considerations

1. Selecting Fireplace Locations

2. Locating Fireplace & Chimney

C. Tools and Supplies Needed

D. Inspect Fireplace and Components

E. Fireplace System Requirements

3 Framing and Clearances

A. Appliance Dimensions/Weight

B. Clearances

Minimum Clearances to Combustibles

C. Construct the Chase

D. Frame the Fireplace

E. Secure and Level the Fireplace

F. Protective Metal Hearth Strips

G. Outside Air Kit (optional)

4 Chimney and Termination Requirements

A. Chimney Requirements

B. Offsets/Returns

C. Termination Requirements

5 Chimney Installation

A. Typical Chimney System

B. Assemble Chimney Sections

C. Secure Offset/Return

D. Install Ceiling Firestops

E. Install Attic Insulation Shield

F. Roof Penetration

G. Install Chase/Chase Top

H. Termination Cap Requirements

I. Install Termination Cap

6 Shrouds

A. Radiation Shield

B. Field Constructed Shrouds

1. Open Top Shroud

2. Mailbox Style Shroud

3. Roofed Style Shroud

7 Finishing

A. Finishing Material

B. Hearth Extension, Building and Finishing

1. Fireplace Installed Flush on the Floor

and Hearth Extension Raised to Bottom

of Firebox Opening

2. Raised Hearth Extension and Raised Fireplace

3. Fireplace Opening and Hearth Extension Flush

with the Floor

C. Non-Combustible Sealant Material

D. Mantel and Wall Projections

E. Sidewalls/Surrounds

8 Fireplace Setup

A. Gas Log/Lighter Provision

B. Wood Burning Inserts

9 Reference Materials

A. Chimney Components

B. Optional Components

►

Содержание SA42R









































Результаты поиска

Содержание SA42R

Отзывы:

Похожие инструкции для SA42R

Бренды по названию

Популярные бренды

Majestic SA42R, Руководство по установке

Результаты поиска

Содержание SA42R

Отзывы:

Похожие инструкции для SA42R

Бренды по названию

Популярные бренды