Majestic MARQUIS MARQ36IN-B страница 50 Скачать руководство пользователя

Страница: 50 / 69

Majestic MARQ36IN-B, MARQ42IN-B Installation Manual • 2614-980 Rev. D • 4/19

D. Decorative Barrier Front Dimensions for

Finishing

A decorative barrier front is required for this appliance.

Only decorative barrier fronts certified for use with this

appliance model may be used. Contact your dealer for

a list of decorative barrier fronts that may be used. Once

you have determined what kind of decorative barrier front

and finishing material is going to be used on the fireplace,

you may use the table below which shows the decorative

barrier front models and the finishing material thickness

allowed. For an inside fit there is an available template to

ensure that proper decorative barrier front clearances are

maintained with finishing material with thickness greater

than 1 inch.

COMBUSTIBLE MATERIAL

Figure 10.11 Inside Fit Decorative Barrier Fronts

The decorative barrier fronts approved for use with this

appliance have been designed to be installed by two

methods: Overlap Fit or Inside Fit. Before beginning the

installation, it is important to determine with method will

be used.

Overlap Fit Method:

These decorative barrier fronts

have been designed to be installed over finishing mate

rial up to one inch thick.

Inside Fit Method:

These decorative barrier fronts may

be recessed into non-combustible finishing material up to

10 inches thick.

NOTICE:

Proper clearances from the fireplace opening

to any finishing material thicker than 1 inch MUST be

maintained.

NOTE:

Finishing templates are included with this product.

See Section 10.B.

DIMENSIONS

3/4 IN.

1-1/4 IN.

Approved Decorative Barrier Fronts: FSMQ36,

FSMQ42

Содержание MARQUIS MARQ36IN-B






































































Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды

Majestic MARQUIS MARQ36IN-B, Руководство по установке

Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды