Majestic MARQUIS MARQ36IN-B страница 45 Скачать руководство пользователя

Страница: 45 / 69

Majestic MARQ36IN-B, MARQ42IN-B Installation Manual • 2614-980 Rev. D • 4/19

Finishing

Figure 10.1 Non-combustible Facing Diagram

0 in.

NON-COMBUSTIBLE

BOARD

COMBUSTIBLE MATERIAL

0 IN.

MODEL

in.

MARQ36IN-B

1549

57-5/8

1464

MARQ42IN-B

1702

62-5/8

1591

A. Facing Material

NOTICE:

Surface temperatures around the appliance will

become warm while the appliance is in operation. Ensure

finishing materials used for all surfaces (floor, walls,

mantels, etc.) will withstand temperatures up to 190

Risk of Fire!
DO NOT

apply combustible materials beyond the min-

imum clearances.

Comply with all minimum clearanc-

es to combustibles as specified in this manual.

terials overlapping into non-combustible zones could

ignite and will interfere with air flow through decorative

barrier fronts.

• Metal front of appliance may be covered with non-

combustible materials only.

• Facing and/or finishing materials must not interfere

with air flow through

decorative barrier fronts, removal

of decorative barrier fronts or access for service.

• Facing and/or finishing materials must never

overhang into the glass opening.

• Observe all clearances when applying combustible

materials.

• Seal gaps between the finished wall and appliance

top and sides using a 300 ºF minimum sealant. Refer

to Figure 10.1.

WARNING

Содержание MARQUIS MARQ36IN-B






































































Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды

Majestic MARQUIS MARQ36IN-B, Руководство по установке

Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды