Majestic MARQUIS MARQ36IN-B страница 27 Скачать руководство пользователя

Страница: 27 / 69

Majestic MARQ36IN-B, MARQ42IN-B Installation Manual • 2614-980 Rev. D • 4/19

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire!

Maintain air space clearance

to vent.

DO NOT

pack insulation or other combustibles:

• Between ceiling firestops

• Between wall shield firestops

• Around vent system
Failure to keep insulation or other material away from

vent pipe may cause overheating and fire.

Vent Clearances and Framing

Figure 5.2 Wall Penetration

Figure 5.1 Horizontal Venting Clearances To Combustible

Materials

B. Wall Penetration Framing/Firestops

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must

frame a hole for the wall shield firestop(s). The wall shield

firestop maintains minimum clearances and prevents cold

air infiltration.

• The opening must be framed on all four sides using the

same size framing materials as those used in the wall

construction.

• DVP pipe - A wall shield firestop is required on one side

only on interior walls. If your local inspector requires a

wall shield firestop on both sides, then both wall shield

firestops must have a heat shield (refer to Section

12.A.) attached to them.

• See Section 7.E. for information for regarding the instal-

lation of a horizontal termination cap.

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).

•

DVP heat shield

- designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184

mm)

thick

• If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If

wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.

• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.

If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.

(DVP Pipe Shown)

3 in. (76 mm)

top clearance *

1 in. (25 mm)

clearance

bottom & sides

Heat

Shield

Wall

Shield

Firestop

Heat

Shield

WALL

3 in. (76 mm)

top clearance

1 in. (25 mm)

clearance around

vertical sections

10 in.

12 in.

DO NOT PACK WITH

INSULATION OR OTHER

MATERIAL

* Shows center of vent framing hole with minimum vertical for top venting. The

center of the hole is one (1) in. (25 mm) above the center of the horizontal

vent pipe.

MODEL

MARQ36IN-B NG/

Propane

74-3/16 in.

73-3/16 in.

MARQ42IN-B NG

79-3/16 in.

78-3/16 in.

MARQ42IN-B Propane

91-3/16 in.

90-3/16 in.

Non-Combustible Wall Penetration

If the hole being penetrated is surrounded by non-com-

bustible materials such as concrete, a hole with diameter

one inch greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall

shield firestop is only required on one side and no heat

shield is necessary.

Содержание MARQUIS MARQ36IN-B






































































Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды

Majestic MARQUIS MARQ36IN-B, Руководство по установке

Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды