Majestic MARQUIS MARQ36IN-B страница 7 Скачать руководство пользователя

Страница: 7 / 69

Majestic MARQ36IN-B, MARQ42IN-B Installation Manual • 2614-980 Rev. D • 4/19

D. Inspect Appliance and Components

• Carefully remove the appliance and components from

the packaging.

• The vent system components and decorative barrier

fronts may be shipped in separate packages.

• If packaged separately, the log set and appliance grate

must be installed.

• Report to your dealer any parts damaged in shipment,

particularly the condition of the glass.

• This product is factory-equipped with an IntelliFire™

Touch remote control, which was paired to the appliance

at the factory. This specific remote control needs to

remain with the contents of the manual bag. Do not

install batteries in the remote control until performing the

final appliance setup and checklist.

•

Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the

installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion!

Damaged parts

could impair safe operation.

DO NOT i

nstall damaged, in

complete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for,

and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent system

component.

• Modification of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass assembly.
• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING! Risk of Fire, Explosion or Electric Shock!

DO NOT

use this appliance if any part has been under

water. Call a qualified service technician to inspect the

appliance and to replace any part of the control system

and/or gas control which has been under water.

Содержание MARQUIS MARQ36IN-B






































































Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды

Majestic MARQUIS MARQ36IN-B, Руководство по установке

Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды