Majestic MARQUIS MARQ36IN-B Скачать руководство пользователя страница 3

Страница: 3 / 69

Majestic MARQ36IN-B, MARQ42IN-B Installation Manual • 2614-980 Rev. D • 4/19

Installation Standard Work Checklist

Customer:

Lot/Address:

Model (circle one): MARQ36IN-B, MARQ42IN-B

Date Installed:

Location of Fireplace:

Installer:

Dealer/Distributor Phone #

Serial #:

Comments Communicated to party responsible ____________________ by ______________________on ___________

(Builder / Gen. Contractor/) (Installer) (Date)



= Contains updated information.

Hearth & Home Technologies recommends the following:

• Photographing the installation and copying this checklist for your file.

• That this checklist remain visible at all times on the appliance until the installation is complete.

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in

this installation manual.

WARNING! Risk of Fire or Explosion!

Failure to install appliance according to these instructions can lead to a

fire or explosion. Install ONLY components and accessories approved by Hearth & HOme Technologies. Unap

proved components and accessories could cause fireplace to overheat.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Appliance Install Information

YES IF NO, WHY?

Verified clearances to combustibles requirements are maintained. (Pg. 11-12) ___________________

Verified that the chase is insulated and sealed. (Pg. 13)

___________________

Verified mantel and wall clearance requirements are maintained. (Pg. 48-49) ___________________

Verified hearth extension requirements are maintained. (Pg. 15) ___________________

Verified appliance is leveled and secured. (Pg. 31) ___________________

Verified required factory-supplied non-combustible board installed. (Pg. 32) ___________________

Venting/Chimney Section 7 (Pg. 33-38)

Verified venting configuration complies to vent diagrams.

___________________

Verified venting installed, locked and sealed/secured in place.

___________________

Verified venting meets clearance to combustible requirements. ___________________

Verified wall/ceiling firestops are installed (if applicable).

___________________

Verified attic insulation shield is installed (if applicable).

___________________

Verified Exterior wall/Roof flashing is installed and sealed.

___________________

Verified termination cap is installed and sealed.

___________________

Electrical Section 8 (Pg. 39-42)

Verified unswitched power (110-120 VAC) provided to the appliance.

____

_______________

Verified wall switch wires are properly installed (if applicable).

___________________

Gas Section 9 (Pg. 45-50)

Verified appliance is using proper fuel type.

___________________

If converted, verified proper fuel conversion kit was used.

___________________

Verified that gas components (fittings, pressure taps, etc) are leak free and fireplace is

operating under correct pressures. ___________________

Finishing Section 10 (Pg. 45-50)

Verified that finish material does not interfere with install/operation of decorative barrier front

___________________

Verified combustible materials are not

installed in non-combustible areas.

___________________

Verified all clearances meet installation manual requirements.

___________________

Verified mantels/wall projections comply with installation manual requirements.

___________________

Appliance Setup Section 11 (Pg. 51-62)

Verified all packaging and protective materials are removed (inside & outside of appliance). ___________________

Verified Teco-Sil installed and properly fogged with black high temperature paint. ___________________

Verified Lava Rock, Mystic Embers, Glowing Embers, and logs installed correctly. ___________________

Verified fixed glass assembly installed and secured. ___________________

Verified that a required decorative door option is installed properly. ___________________

Verified remote control has been programmed and is fully functional. ___________________

Verified proper air shutter setting for installation type and vent configuration. ___________________

Manual bag and all of its contents are removed from inside/under

the appliance and given to party responsible for use and operation. ___________________

2614-982 1/19

Comments:

Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective

action needed ____________________________________________________________________________________

Содержание MARQUIS MARQ36IN-B






































































Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Бренды по названию

Популярные бренды

Majestic MARQUIS MARQ36IN-B, Руководство по установке

Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Бренды по названию

Популярные бренды