Majestic Designer Скачать руководство пользователя

Страница: 15 / 56

53D0419

INSTALLATION PRECAUTIONS

Consult local building codes before beginning the installation. The installer must make sure

to select the proper vent system for installation. Before installing vent kit, the installer must

read this fireplace manual and vent kit instructions.
Only a qualified installer/service person should install venting system. The installer must

follow these safety rules:

•

Wear gloves and safety glasses for protection.

•

Use extreme caution when using ladders or when on rooftops.

•

Be aware of electrical wiring locations in walls and ceilings.

The following actions will void the warranty on your venting system:

•

Installation of any damaged venting component.

•

Unauthorized modification of the venting system.

•

Installation of any component part not manufactured or approved by MHSC.

•

Installation other than permitted by these instructions.

FINIShING MATERIAL

NOTE: Any wiring (i.e. remote control, wall switch, and optional fan) must be done

prior to final finishing to avoid costly reconstruction.

INSTALLATION INFORMATION

Only noncombustible materials (i.e. brick, tile, slate, steel, or other materials with a UL fire rating of

Zero) may be used to cover the black surface of the appliance. A 300

F minimum adhesive may be

used to attach facing materials to the black surface. If joints between the finished wall and the fireplace

surround are sealed, a 300

F minimum sealant material (General Electric RTV103 or equivalent) must

be used.

VENT INSTALLATION

ARNING

Never obstruct or modify the air inlet

or outlet grills (louvers). This may

create a fire hazard.

ARNING

Failure to follow these

instructions will void the

warranty.

Read all instructions completely and thoroughly before attempting

installation. Failure to do so could result in serious injury, property

damage or loss of life. Operation of improperly installed and maintained

venting system could result in serious injury, property damage or loss

of life.

ARNING

Содержание Designer

























































Результаты поиска

Содержание Designer

Отзывы:

Похожие инструкции для Designer

Бренды по названию

Популярные бренды

Majestic Designer, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Designer

Отзывы:

Похожие инструкции для Designer

Бренды по названию

Популярные бренды