Majestic Designer Скачать руководство пользователя страница 29

Страница: 29 / 56

53D0419

FIREPLACE INSTALLATION

ChECK GAS TyPE

Use proper gas type for the fireplace you are installing. If you have conflicting gas type, do

not install fireplace. See dealer where you purchased the fireplace for proper fireplace for

your gas type or conversion kit.

INSTALLING GAS PIPING TO FIREPLACE / BURNER SYSTEM LOCATION

INSTALLATION ITEMS NEEDED

Before installing fireplace and burner system, make sure you have the items listed below.

• External regulator (supplied by installer) • Piping (check local codes) • Sealant (resistant to propane/LP gas)

• Equipment shutoff valve*

• Test gauge connection*

• Sediment trap (recommended)

• Tee joint

• Pipe wrench

• approved flexible gas line with gas connector (if allowed by local codes — not provided)

* A CSA design-certified equipment shutoff valve witH 1/8" NPT tap is an acceptable alternative to test gauge

connection. Purchase the CSA design-certified equipment shutoff valve from your dealer.

For propane/LP connections only, the installer must supply an external regulator. The external regulator will reduce

incoming gas pressure. You must reduce incoming gas pressure to between 11 and 13 inches of water. If you do

not reduce incoming gas pressure, burner system regulator damage could occur. Install external regulator with

the vent pointing down as shown in

Figure 38.

Pointing the vent down protects it from freezing rain or sleet.

FP1977
external regulator

Figure 38 -

External Regulator with Vent Pointing Down

(Propane/LP Only)

FP1977

External

Regulator

100 lb. (min)

Propane/LP

Supply Tank

Vent Pointing

Down

When using copper of flex connectors use only fittings

approved for gas connections. The gas control inlet is

3/8" NPT.

ARNING

A qualified installer or service person

must connect appliance to gas supply.

Follow all local codes.

CAUTION

Use only new black iron or steel pipe.

Internally tinned copper or copper

tubing can be used per National

Fuel Code, section 2.6.3, providing

gas meets hydrogen sulfide limits,

and where permitted by local codes.

Gas piping system must be sized

to provide minimum inlet pressure

(listed on data plate) at the maximum

flow rate (BTU/hr). Undue pressure

loss will occur if the pipe is too

small.

All electric heaters have hot and arcing

or sparking parts inside. Do not store

or use gasoline or other flammable

vapors and liquids in the vicinity of

this or any other appliance.

CAUTION

Содержание Designer

























































Результаты поиска

Содержание Designer

Отзывы:

Похожие инструкции для Designer

Бренды по названию

Популярные бренды

Majestic Designer, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Designer

Отзывы:

Похожие инструкции для Designer

Бренды по названию

Популярные бренды