Magnetrol Pulsar R86 Скачать руководство пользователя

Страница: 27 / 61

58-641 PULSAR Model R86 Pulse Burst Radar Transmitter - F

OUNDATION

fieldbus

™

Instruction Manual

CLOCK_PER

: Establishes the period for periodic reset, in

hours.

PRE_TRIP

: Adjusts the amount of mass, volume or energy

that should set OUT_PTRIP when the integration reaches
(TOTAL_SP-PRE_TRIP) when counting up of PRE_TRIP
when counting down.

N_RESET

: Counts the number of resets. It cannot be

written or reset.

PCT_INC

: Indicates the percentage of inputs with “good”

status compared to the ones with “bad” or “uncertain” and
“bad” status.

GOOD_LIMIT

: Sets the limit for PCT_INC. OUT.

Receives the status “Good” is PCT_INCL

≥

GOOD_LIM.

UNCERTAIN_LIMIT

: Sets the limit for PCT_INC.

OUT receives the status “uncertain” if PECT_INC

≥

UNCERT.LIM.

OP_CMD_INT

: Operator command RESET Resets the

totalizer

OUTAGE_LIMIT

: The maximum tolerated duration for

power failure

RESET_CONFIRM

: Momentary discrete value with can

be written by a host to enable further resets, if the option
“Confirm reset” in INTEG_OPTIONS is chosen.

UPDATE_EVT

: This alert is generated by any changes to

the static data.

BLOCK_ALM

: Used for all configuration, hardware, con-

nection failure, or system problems in the block.

BLOCK_ERR_DESC

: Reports more specific details regard-

ing some errors reported through BLOCK_ERR.

3.2

Arithmetic Block (AR)

The Arithmetic function block provides the ability to con-
figure a range extension function for a primary input and
applies the nine different arithmetic types as compensation
to or augmentation of the range extended input.

The nine arithmetic functions are:

• Flow Compensation Linear

• Flow Compensation Square Root

• Flow Compensation Approximate

• Btu Flow

• Traditional Multiply and Divide

Содержание Pulsar R86






























































Результаты поиска

Содержание Pulsar R86

Отзывы:

Похожие инструкции для Pulsar R86

Бренды по названию

Популярные бренды

Magnetrol Pulsar R86, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Pulsar R86

Отзывы:

Похожие инструкции для Pulsar R86

Бренды по названию

Популярные бренды