Mackie DC16 страница 21 Скачать руководство пользователя

Страница: 21 / 84

DC16 Owner’s Manual

Power Connector

Push the locking multi-pin connector (flat side up) of the power supply into the power connector of the

control surface. Push the line cord securely into the power supply and plug the other end into a grounded

AC outlet. These are included in the packaging.

Make sure that the AC power is matched to the AC power indicated on the rear panel

(below the power connector).

Warning:

Disconnecting the plug’s ground pin is dangerous. Don’t do it!

In fact, it’s a bad idea to remove

anything

from – or add anything to, for that matter – the line

cord. Again, don’t do it!

Power Switch

Press the top of this rocker switch in to turn the DC16 on and press the bottom

of this switch to turn it off.

As a general guide, the Wi-Fi router should be turned on first,

then the DL32R followed by the DC16 and external power amplifiers

or powered speakers. As such, the DC16 and DL32R should also

be turned off last. This will reduce the possibility of any turn-on

or turn-off thumps in the PA.

Technically the DC16 will still be able to discover the DL32R

even if the DC16 is powered on first, but you might be required

to refresh the mixer list the DC16 received.

Lamp Input Jack

The 4-pin XLR connector located next to the power switch allows connection

of a 12V gooseneck lamp. Simply line up the pins and holes and push until

it locks – ‘clicks’ – in place.

There is sufficient current provided to allow using high-intensity

[5 watt, 420 mA] halogen lamps.

The

Power

Block

Flat side (with arrows

and lines) on top.

Push to lock,

pull (on outlined area)

to unlock and remove.

Содержание DC16





















































































Результаты поиска

Содержание DC16

Отзывы:

Похожие инструкции для DC16

Бренды по названию

Популярные бренды

Mackie DC16, Руководство пользователя

Результаты поиска

Содержание DC16

Отзывы:

Похожие инструкции для DC16

Бренды по названию

Популярные бренды