MacDon D1X Series Скачать руководство пользователя страница 78

Страница: 78 / 108

214778

Revision A

5.12

Lubricating the Header

Table 5.4 Recommended Lubricant

Specification

Description

Use

SAE multipurpose

High temperature, extreme pressure (EP2) performance with 1%
max molybdenum disulphide (NLGI Grade 2) lithium base

As required unless
otherwise specified

SAE multipurpose

High temperature, extreme pressure (EP) performance with 10%
max molybdenum disulphide (NLGI Grade 2) lithium base

Driveline slip-joints

5.12.1

Greasing Procedure

Greasing points are identified on the machine by decals showing a grease gun and grease interval in hours of operation.
Grease point layout decals are located on the header.

WARNING

To avoid bodily injury or death from unexpected start-up of machine, always stop engine and remove key from ignition
before leaving operator

’

s seat for any reason.

1001335

Figure 5.43: Single-Knife Header Grease Point
Layout Decal

Wipe grease fitting with a clean cloth before greasing to
avoid injecting dirt and grit.

IMPORTANT:

Use clean, high-temperature, extreme-pressure grease only.

Inject grease through fitting with grease gun until grease
overflows fitting (except where noted).

Leave excess grease on fitting to keep out dirt.

Replace any loose or broken fittings immediately.

Remove and thoroughly clean any fitting that will not take
grease. Also clean lubricant passageway. Replace fitting if
necessary.

1001333

Figure 5.44: Double-Knife Header Grease Point
Layout Decal

PERFORMING PREDELIVERY CHECKS

Содержание D1X Series













































































































Результаты поиска

Содержание D1X Series

Отзывы:

Бренды по названию

Популярные бренды

MacDon D1X Series, Инструкции по разгрузке и сборке

Результаты поиска

Содержание D1X Series

Отзывы:

Бренды по названию

Популярные бренды