MacDon D1X Series Скачать руководство пользователя страница 42

Страница: 42 / 108

214778

Revision A

1006380

Figure 4.12: Lifting the Reel

–

Double Reel Only

For double reel only:

Position sling (A) around the reel tube near the reel center
support arm.

Lift reel to gain access to the center lift cylinder.

Remove shipping wire and banding from center reel lift
cylinder.

1019106

Figure 4.13: Reel Arm Braces

10.

For double reel only:

Remove 3/4 in. socket head bolt and 5/8 in. nut from
cylinder rod end. Retain hardware.

Attach rod end of cylinder (B) to reel arm with socket head
bolt and nut (A). Access hardware through holes in reel arm
braces.

Torque bolt and nut (A) to 54

–

61 Nm (40

–

45 lbf·ft).

Remove pin at barrel end of cylinder.

Adjust reel height so pin can be installed at barrel end of
cylinder and mounting structure.

1008131

Figure 4.14: Outboard Reel Arm

11. Reposition the sling (A) around reel tube near the opposite

outboard reel arm.

12. Remove shipping wire and banding from the reel lift

cylinder.

ASSEMBLING THE HEADER

Содержание D1X Series













































































































Результаты поиска

Содержание D1X Series

Отзывы:

Бренды по названию

Популярные бренды

MacDon D1X Series, Инструкции по разгрузке и сборке

Результаты поиска

Содержание D1X Series

Отзывы:

Бренды по названию

Популярные бренды