MacDon D1X Series Скачать руководство пользователя страница 105

Страница: 105 / 108

214778

Revision A

Predelivery Checklist

Perform these checks prior to delivery to your Customer.

Adjustments are normally not required as the machine is

factory-assembled and adjusted.

If adjustments are required, refer to the appropriate page number in this manual. The

completed Checklist should be retained by either the Operator or the Dealer.

CAUTION

Carefully follow the instructions given. Be alert for safety related messages that bring your attention to hazards and
unsafe practices.

Header Serial Number:

Table .18 Predelivery Checklist for D1X and D1 XL Series Draper Headers

–

North America

Item

Reference

Check for shipping damage or missing parts. Be sure all
shipping dunnage is removed.

—

Check for loose hardware. Tighten to required torque.

8.1 Torque Specifications, page 81

Check tire pressure (Transport/Stabilizer Option).

5.1 Checking Tire Pressure

–

Transport and Stabilizer

Wheels, page 49

Check wheel bolt torque (Transport/Stabilizer Option).

5.2 Checking Wheel Bolt Torque, page 50

Check knife drive box breather position.

5.3 Checking Knife Drive Box, page 51

Check knife drive box lube level.

5.3 Checking Knife Drive Box, page 51

Check knife drive belt(s) tension.

5.4 Checking and Adjusting Knife Drive Belt Tension,
page 53

Check if reel is centered between header endsheets.

5.5 Centering the Reel, page 57

Grease all bearings and U-joints.

5.12 Lubricating the Header, page 72

Check draper tension.

5.6 Adjusting Draper Tension, page 59

Check draper seal.

5.7 Checking and Adjusting Draper Seal, page 61

Check reel tine to cutterbar clearance.

5.10.1 Measuring Reel Clearance, page 65

Check if skid shoes are evenly adjusted an appropriate setting
for first crop.

5.8 Checking and Adjusting Skid Shoe Settings, page
63

Check fit of endshields.

5.11 Checking and Adjusting Endshields, page 68

Check that header is level.

5.9 Leveling the Header, page 64

Check hydraulic hose and wiring harness routing for clearance
when raising or lowering header and reel.

—

Run-up procedure

6 Running up the Header, page 77

Check if the knife drive pulley(s) is rotating in proper
direction: clockwise on left side; counterclockwise on right
side (double knife only).

5.4 Checking and Adjusting Knife Drive Belt Tension,
page 53

Check if lights are functional.

—

Check if reel lift cylinders extend fully.

—

Check if reel moves fully fore and aft.

—

Содержание D1X Series













































































































Результаты поиска

Содержание D1X Series

Отзывы:

Бренды по названию

Популярные бренды

MacDon D1X Series, Инструкции по разгрузке и сборке

Результаты поиска

Содержание D1X Series

Отзывы:

Бренды по названию

Популярные бренды