manualshive.com logo in svg

MacDon D1X Series, Инструкции по разгрузке и сборке

Поделиться
Скачать
MacDon D1X Series Скачать руководство пользователя страница 59

214778

53

Revision A

5.4

Checking and Adjusting Knife Drive Belt Tension

Proceed to the section that applies to the header

’

s knife drive configuration:

•

5.4.1 Checking and Tensioning, page 53

•

5.4.2 Tensioning Timed Knife Drive Belts, page 54

•

5.4.3 Tensioning Timed Knife Drive V-Belts, page 56

Single-knife headers have one knife-drive belt and double-knife headers have two knife-drive belts.

5.4.1

Checking and Tensioning

WARNING

To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key before making
adjustments to machine.

IMPORTANT:

To prolong the belt and drive life, do

NOT

overtighten the belt.

1.

Open the left endshield.

1022180

A

B

C

Figure 5.5: Knife Drive

NOTE:

Belt guide removed for illustration purposes.

2.

Loosen the two bolts (A) securing the motor assembly to
the header endsheet.

3.

Check drive belt tension. A properly tensioned drive belt (C)
should deflect 24

–

28 mm (15/16

–

1-1/8 in.) when 133 N

(30 lbf) of force is applied at the midspan. If the belt needs
to be tensioned, turn the adjuster bolt (B) clockwise to
move the drive motor until proper tension is set.

1002468

A

B

C

Figure 5.6: Knife Drive

4.

Ensure the clearance between belt (A) and belt guide (B) is
1 mm (1/16 in.).

5.

Loosen the three bolts (C), and adjust the position of
guide (B) as required.

6.

Tighten the three bolts (C).

7.

Close the endshield.

8.

Double-knife headers only:

Repeat procedure on the other

side of the header.

PERFORMING PREDELIVERY CHECKS

Содержание D1X Series













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды