Mac allister Titan TTK550LWM Скачать руководство пользователя страница 36

Страница: 36 / 44

INTERVENTIONS ON THE MACHINE
Aligning the cutting-means assembly

The cutting-means assembly should

be properly adjusted to obtain an

evenly mown lawn.

If mowing is uneven, check the tyre

pressure.

If this is not sufficient to achieve an

even cut, please contact your Dealer

to adjust the alignment of the cutting-

means assembly.

Replacing the wheels

Stop the machine on flat ground and

put a block under a load-bearing part

of the frame on the side that the wheel

is to be changed.

The wheels are held by a snap ring (1)

which can be removed with a screw-

driver.

NOTE

If you have to replace one or

both rear wheels, make sure that any

differences in their external diameter

does not exceed 8-10 mm; on the

contrary, you must adjust the cutting-

means assembly alignment to prevent

uneven mowing.

IMPORTANT

Before remounting

the wheel, apply grease to the axle. Put

the snap ring (1) and shoulder washer

(2) back in place.

Repairing or replacing tyres

All puncture repairs or replacements will have to be carried out by a tyre repair expert in ac-

cordance with the methods for the kind of tyre used.

Replacing a fuse

The electric system and the electronic circuit board are protected by a fuse. When it blows

the machine stops. In this case, remove the cover (1) to reach the fuse (2) next to the bat-

tery. The fuse capacity is indicated on the fuse.

Care and maintenance

mor

detail

...

TTK550LWM by TITAN

Содержание Titan TTK550LWM













































Результаты поиска

Содержание Titan TTK550LWM

Отзывы:

Похожие инструкции для Titan TTK550LWM

Бренды по названию

Популярные бренды

Mac allister Titan TTK550LWM, Руководство пользователя

Результаты поиска

Содержание Titan TTK550LWM

Отзывы:

Похожие инструкции для Titan TTK550LWM

Бренды по названию

Популярные бренды