M2 Antenna Systems RC2800PRKX2SU Скачать руководство пользователя страница 24

This warranty gives you specific legal rights. You may also have other rights which will vary from state to state 

or province to province.

 

 

M2

 warrants the 

RC2800PRKX2SUMC

 two Axis Controller unit against defects in material and workmanship for 

a  

period of 12 months 

from date of purchase. During the warranty period, 

M2

 will, at its option, either repair or 

replace products or components which prove to be defective. The warranty shall not apply to defects or damage 

resulting from:

 

 

• 

Improper or inadequate maintenance by user

 

• 

Improperly prepared installation site

 

• 

Unauthorized modifications or misuse

 

• 

Accident, abuse, or misapplication

 

• 

Normal wear

 

 

 

M2

  specifically  does  not  warrant  this  product  for  any  direct,  indirect,  consequential,  or  incidental        

damages  arising  from  the  use  or  inability  to  use  the  product.  Some  states  or    provinces  do  not  allow  the         

exclusion or limitation of liability for consequential or incidental damages so the above limitation may not apply.

 

 

 

In the event repair or replacement are necessary, purchaser shall contact M2 for return  authorization. In 

many cases this contact can simplify and expedite the repair / replacement process and help reduce costs and 

downtime.

 

 

 

The purchaser shall be responsible for packing the product properly for return and for charges to ship 

the product to 

M2

. Always include with the shipment, a statement detailing the problem / failure and any other 

pertinent observations. Insuring the product for shipment is  recommended. Use the original packing materials 

whenever possible. 

M2 

is responsible for charges 

(in  the  United  States) 

to return the repaired / replacement 

product only where warranty service is involved.

 

 

 

 

 

 

M2 Antenna Systems, Inc.  4402 N. Selland Ave. Fresno, CA 93722

 

(559) 432

-

8873 Fax (559) 432

-

3059 Web: www.m2inc.com

 

12 Month Limited Warranty

 

WARRANTY INFO

 

Содержание RC2800PRKX2SU

























Отзывы: