LXE MX1-IS Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 164

background image

54

BIOS Setup

MX1 I-Safe Reference Guide

E-EQ-MX1ISRG-F

Post Msg

Set this parameter to On to stop the boot process if the Power On Self Test (POST) procedure
encounters errors. Otherwise, the system continues to attempt to boot despite many startup error
messages that display.

See “System Testing” for more information on POST messages.

Values: On,

Off

Default: Off

A parameter setting of On only affects the following error conditions (messages are displayed)
and the bootup is halted:

Messages that Halt Bootup

•

IDE Unit Error

No media connected
Configured for 0 cylinders
Controller reset failed
Media not ready
Track 0 seek timed out
Media initialization failed
Media recalibration failed

Last track seek failed

•

Timer Error

System timer (0) failed

•

Disk Error for Debug

Floppy type does not match setup only for debug capabilities

•

I/O Chip Error

I/O conflicts exist for serial ports, parallel ports, and IDE units (any or all)

•

Other Error

IRQ conflict, unsupported COM port configuration, keyboard locked

Bootup Continues after These Messages

This option does not affect the following error conditions (messages are displayed and the bootup
continues):

•

Keyboard Error

Keyboard reset failed
Keyboard interrupts failed

•

CMOS Error

CMOS checksum failed
CMOS time and date not set
Real time clock failure

•

Configuration Error

Previous POST execution was incomplete

•

Scanner Error

Scanner detected, but attempts to read scanner configuration failed.

«
...
62
63
64
65
66
...
»

Содержание MX1-IS





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX1-IS

Бренд: Intermec Страницы: 74

Бренд: Speedata Страницы: 10

Бренд: Assistech Страницы: 4

Бренд: IBM PC Страницы: 52

7900L00-414C50E - Hand Held Products Dolphin...

Бренд: Hand Held Products Страницы: 242

Бренд: iDiPOS Страницы: 44

Бренд: AMobile Страницы: 60

Бренд: HandHeld Страницы: 12

PEG-NZ90 - Personal Entertainment Organizer

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

PEG-S360 - Personal Entertainment Organizer

Бренд: Sony Страницы: 31

Бренд: MWg Страницы: 152

Бренд: Symbol Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды