8
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036 U.S.A.
Made and printed in U.S.A.
P/N 040-227-12 Rev. A 1/05
Limited Warranty
Lutron EA Ltd. (“Lutron EA”) warrants each unit to be free from defects in material and
workmanship and to perform under normal use and service. To the extent permitted by law,
Lutron EA and Lutron Electronics Co. Inc. (“Lutron”) make no warranties or representations as
to the units except as set forth herein. This warranty shall run for a period of one year from the
date of purchase and Lutron’s obligations under this warranty are limited to remedying any
defect, replacing any defective part or replacement (at Lutron EA’s sole option) and shall be
effective only if the defective unit is shipped to Lutron EA postage prepaid within 12 months
after purchase of the unit, to the extent permitted by law. Repair or replacement of the unit
does not affect the expiry date of the warranty. This warranty does not cover damage or
deficiencies due to abuse, misuse, inadequate wiring or insulation or use or installation other
than in accordance with instructions accompanying the unit.
Although every attempt is made to ensure that catalogue information is accurate and up-to-
date, please check with Lutron EA before specifying or purchasing this equipment to confirm
availability, exact specifications, and suitability for your application.
This warranty does not affect the statutory rights of consumer purchasers of the unit.
These products may be covered by one or more of the following US patents: 4,835,343;
4,924,349; D422,567; D436,930; D453,742; D456,783; D461,782; D465,460; D465,770;
D466,090; D466,091; D466,484; D475,024; D475,025; and corresponding foreign patents.
US and foreign patents pending. Lutron, the Sunburst logo, and Sivoia are registered
trademarks, and Sivoia QED is a trademark of Lutron Electronics Co., Inc.
© 2005 Lutron Electronics Co., Inc.
Note:
The current position is stored as a preset only on the
EDUs that are assigned to that preset button. The preset is only
accessable from that particular Keypad.
Troubleshooting
For information on troubleshooting, please refer to the
Sivoia
QED
Wiring and Programming Guide.
Storing Presets
Sivoia QED
EDUs have the ability to store positions as presets.
1. Set all EDUs controlled by the Keypad to the desired level
using the Raise (
) and Lower (
) buttons on the
Keypad.
2. Store the EDUs’ current position as a preset by pressing
and holding the desired Preset (
) button for 5 seconds.
The LED next to the Preset button (
) on the Keypad will
flash and then turn on, indicating that the preset has been
stored.
Technical Assistance
EUROPEAN HEADQUARTERS
Lutron EA Ltd.
6 Sovereign Close
London, E1W 3JF
United Kingdom
Tel: +44-(0)20-7702-0657
Fax: +44-(0)20-7480-6899
CUSTOMER SERVICE/ORDERING
UK +44-(0)20-7702-0657 –
09.00 - 18.00 GMT
USA +1-610-282-3800 –
08.00 - 20.00 EST
CUSTOMER SERVICE/E-MAIL
TECHNICAL SUPPORT & SERVICES
UK +44-(0)20-7702-065709.00 -
18.00 GMT
USA +1-610-282-3800 – 24 hours/7
days
INTERNET: www.lutron.com
WORLD HEADQUARTERS
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036
United States
Tel: +1-610-282-3800
Fax:+1-610-282-1243
Press the Preset (
)
button for 5
seconds.
LED will
flash and
then turn
on.
