background image

®

For additional information, see the complete installation and operation guide at 

www.lutron.com/qs

GRAFIK Eye

®

 QS Control Unit Quick Installation and Operation Guide   5

Wiring the GRAFIK Eye

®

 QS Control Unit:

Line Voltage Wiring Details (continued)

Step 4: Connect line voltage and loads 

to control unit.

•  Strip 8 mm of insulation off the line 

voltage/mains cables in the wallbox.

•  Connect the line voltage/mains, ground, 

and load wires to the appropriate 

terminals on the back of the control unit.

  L: Hot/Live
  N: Neutral
      : Ground

  Terminals 1-6:  Dimmed/Switched 

 

line voltage outputs

 

 8 mm

  The recommended installation torque 

is 0.6 N

∙m for line voltage/mains 

connections and 0.6 N

∙m for the earth/

ground connection.

 

Note:

 See the zone setup section for 

a list of compatible load types and 

instructions for programming the  

GRAFIK Eye

®

 QS control unit to properly 

recognize them.

Notice: Risk of damage to unit.

 GRAFIK Eye

®

 QS control units must be in stalled by 

a qual i fied electrician in accordance with all applica ble reg u la tions and building codes. 

Im prop er  wiring can result in dam age to control units or oth er equipment.

Note: 

To avoid over heat ing and pos si ble damage to  equipment, do not install control 

units to dim re cep ta cles, mo tor-op erated ap pli ances, or flu o res cent lighting not 

equipped with Lutron Hi-lume

®

, Eco-10

®

, Tu-Wire

®

, electron ic dim ming ballasts, or 

other devices approved for your location. In dimmed mag net ic low-voltage cir cuits, 

you can pre vent trans former  overheating and failure by avoid ing excessively high cur-

rent flow. Do not op erate control units with any lamps re moved or burned out; re place 

any burned out lamps imme di ate ly; use only transform ers that in cor po rate ther mal 

pro tection or fused pri ma ry wind ings. Control units are de signed for res i den tial and 

commercial use, for indoor use only.

Содержание QSGR-3PCE





















Отзывы: