LS tractor MT122 страница 106 Скачать руководство пользователя

Страница: 106 / 132

5 - 17

(2) Replacing Hydraulic Oil Filter

①

Main suction filter

Park tractor on level surface and engage parking

brake and lower implements and stop the engine

and cool down the tractor sufficiently.

Loosen the drainage plug, and drain the

transmission oil.

(See page 5-20)

Carefully clean around the filter and set a clean

container under the filter.

Coat clean hydraulic oil on the packing of new

filter and check the packing is placed well in the

groove.

Turn the oil filter counter-clockwise to remove

with filter wrench.

Turn the new filter clockwise to assemble until

the packing makes contact with the mounting

surface. Tighten ¾ to 1 turn more after packing

contact.

Add transmission oil, and run the engine at idle

rpm and check any leakage.

Check the oil level. If necessary, add new oil.

Replace the HST filter according to the same

procedure of the hydraulic oil filter.

②

HST filter (HST Type only)

▶

Make sure to stop the engine before loosening the oil filter.

▶

If the filter or oil is very hot, it may cause serious burns. After cooling down the

tractor sufficiently, replace the filter.

Warning

Main

suction filter

Loosen

Tighten

Loosen

Tighten

HST filter

Содержание MT122





































































































































Результаты поиска

Содержание MT122

Отзывы:

Похожие инструкции для MT122

Бренды по названию

Популярные бренды

LS tractor MT122, Руководство оператора

Результаты поиска

Содержание MT122

Отзывы:

Похожие инструкции для MT122

Бренды по названию

Популярные бренды