LS tractor MT122 Скачать руководство пользователя страница 79

Страница: 79 / 132

4 - 18

(3) Hitch and Drawbar (optional)

When attaching towing equipments, use the

hitch or drawbar. DO NOT use the 3-point

linkage or other parts. If so, the tractor could

turnover.

When attaching towing equipments, do not

exceed the maximum permissible vertical and

horizontal loads.

Hitch

▶

Pulling from the tractor rear axle or any point above the axle may cause the tractor

to overturn. Use always the drawbar or hitch for pulling work.

▶

Do not tow equipment without brakes, weighing more than twice the tractor weight.

▶

When locking the hitch or drawbar with pin after aligning to the towing equipment,

apply the parking brake and stop the engine.

▶

Before transporting equipment on public roads, make sure you comply with your

local traffic regulation.

Caution

Hitch

Drawbar (w/clevis)

Unbraked towable mass

800kg (1764 lb)

Independently braked towable mass

1600kg (3527 lb)

Inertia-braked towable mass

1600kg (3527 lb)

Hydraulic or pneumatic braked towable mass

N/A

Hitch pin

①

Hitch

Vertical load : 400kg (882lbs)

Horizontal load : 1600kg (3527lbs)

②

Drawbar (w/clevis)

It is used to tow the equipment having 2 axles.

It is available to adjust the length of draw bar

(telescopic type) after removing snap pin and

lock pin in the right figure. After adjusting the

length, assemble the pins correctly.

Insert the hitch pin and snap pin correctly after

attaching/detaching the equipment.

Vertical load : 400kg (882lbs)

Horizontal load : 1600kg (3527lbs)

Drawbar

Snap pin

Содержание MT122





































































































































Результаты поиска

Содержание MT122

Отзывы:

LS tractor MT122, Руководство оператора, Страница: 79 / 132

Результаты поиска

Содержание MT122

Отзывы: