LS tractor MT122 страница 44 Скачать руководство пользователя

Страница: 44 / 132

3 - 3

Cold start aid indicator

When turning start-key switch to “

Preheat

”

position, this indicator shall be ON.

When turning start-key switch to “

Start

”

position, this indicator shall be ON as well.

Cruise drive indicator

This indicator shall be ON when pressing the

cruise control switch for applying cruise drive.

Engine coolant temperature gauge

This gauge indicates the temperature of engine coolant.

The closer the needle approaches “

H”

, the higher the temperature of engine coolant is.

If the needle of engine coolant temperature gauge indicates red zone, Stop the engine

immediately and check the engine cooling system. (coolant, radiator screen, fan belt, …)

The radiator and coolant is very hot. When checking the coolant level, comply with instructions of

the section 5 “Maintenance and Lubrication” in this manual.

Tachometer

Tachometer shows running engine speed. (revolutions per minute)

Hour meter

The number 0005.3 in hour meter shows that the tractor has been used for 5.3hours.

(5hours and 18minutes).

This indicator shall be ON when turning the key

switch to ON position, and shall be OFF after

starting engine.

If not, contact your authorized dealer for

checking electrical charging system.

Battery charging indicator

This gauge indicates the remaining amount of

fuel. If the needle indicates “

”, fill the fuel tank

immediately

Fuel level gauge

540/2933

Содержание MT122





































































































































Результаты поиска

Содержание MT122

Отзывы:

Похожие инструкции для MT122

Бренды по названию

Популярные бренды

LS tractor MT122, Руководство оператора

Результаты поиска

Содержание MT122

Отзывы:

Похожие инструкции для MT122

Бренды по названию

Популярные бренды