LS tractor MT122 страница 121 Скачать руководство пользователя

Страница: 121 / 132

5 - 32

ⓑ

Removing Jumper cables

Remove jumper cables as right figure, “Removing

order of jumper cables”.

▶

Pay attention not to change the (+) and (-) pole. If not, it may cause a failure of

electric circuit or the damage of wire and even the polarity of battery can be

changed at over-discharged state.

Notice

< Removing order of jumper cables >

①

②

③

④

Engine

Normal

Discharge

Red cable

Black cable

Caution

▶

The gas generated from the battery can be exploded by spark.

DO NOT connect the negative(-) cable of auxiliary battery to the negative (-)

terminal of tractor battery. Make sure to connect to the engine block.

▶

Keep all flames and sparks away and DO NOT smoke while charging the battery.

④

How to use jumper cables

※

If the battery which is attached to the tractor is discharged and needs to connect a auxiliary battery,

follow the instructions as below.

< Connecting order of jumper cables >

①

②

③

④

Engine

Normal

Discharge

Red cable

Black cable

ⓐ

Connecting Jumper cables

Check followings before connecting the cables.

- Is the spring of clamp normal?

- Is the cable and clamp cut-off?

1. Stop engine, apply parking brake and remove

the ignition key.

2. Connect two (+) terminals of both batteries with

red cable.

(tractor battery-

①

, auxiliary battery-

②

)

3. Connect one end of black cable to (-)

terminal(

③

) of auxiliary battery and the other

end to engine block desired to start (

④

4. Start engine. If the engine does not start,

check the electrolyte level of each battery.

Содержание MT122





































































































































Результаты поиска

Содержание MT122

Отзывы:

Похожие инструкции для MT122

Бренды по названию

Популярные бренды

LS tractor MT122, Руководство оператора

Результаты поиска

Содержание MT122

Отзывы:

Похожие инструкции для MT122

Бренды по названию

Популярные бренды