LS tractor MT122 страница 102 Скачать руководство пользователя

Страница: 102 / 132

5 - 13

(11) Adjusting HST control linkage (HST type)

Run engine and place the range gear shift lever in “Low” position.

Check if the HST tractor stops by taking the foot off from the pedal while driving.

If the tractor does not stop, stop the tractor immediately by using the brake pedal. And, adjust the

neutral position as below.

Adjustment of “NEUTRAL” position

of the HST control.

1. Stop tractor on a flat ground and stop the engine.

2. Lift the rear wheel of the tractor off the ground

sufficiently by using a hoist. If there is no hoist,

use the suitable lifting equipment. For the tractor

weight, refer to the section “6. Dimension and

Specification” in this manual.

3. Place the 4WD lever to “2WD” and apply wheel

chock to the front wheels. It is necessary for the

tractor not to move when engine starts.

4. Set the HST pedals

①②

horizontally by adjusting

the rod

⑥

after loosening the lock nut

⑤

5. Loosen the locking bolt

⑧

and turn left/right

neutral lever

⑦

connected with the locking bolt to

find out neutral position. If the neutral position is

ok, tighten the locking bolt

⑧

▶

When adjusting, DO NOT get close to the cooling fan. It may cause the serious

injury.

▶

When lifting the rear of the tractor, the tractor may incline to the left or right by

oscillating angle of the front axle. Insert the chock between front axle and engine

frame tightly.

Caution

6. After checking that neutral switch

⑩

is pressed

enough, start engine. If not, loosen the screw,

and reset the position of the neutral switch

⑩

7. To adjust the returning speed of the HST pedals,

loosen locking bolt

④

, and adjust the stiffness of

the spring

③

8. After restarting engine, check the neutral position

again.

9. The stroke of the HST forward pedal

①

is about

15˚ when pressing the HST forward pedal. The

retracted stroke of the HST forward pedal is

about 10˚ when pressing HST reverse pedal. If is

not normal, adjust the stopper bolts

⑨

①

②

③

④ ⑤ ⑥

⑦

⑧

⑨

⑩

Содержание MT122





































































































































Результаты поиска

Содержание MT122

Отзывы:

Похожие инструкции для MT122

Бренды по названию

Популярные бренды

LS tractor MT122, Руководство оператора

Результаты поиска

Содержание MT122

Отзывы:

Похожие инструкции для MT122

Бренды по названию

Популярные бренды