Loviband SensoDirect 150 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 40

background image

36

12. ACCESSORIES

Accessories for pH/Redox

Spare electrode for pH, pH 0 – 14, plastic/gel type, BNC-plug
Redox electrode, plastic/gel, BNC-plug

Accessories for pH- and Redox electrodes

pH-Buffer solution set pH 4, pH 7, pH 10 (25°C) colour coded 90 ml each in
plastic bottles, traceable to N.I.S.T
pH Buffer solution 4.00 (25°C) red, 90 ml , traceable to N.I.S.T
pH Buffer solution 7.00 (25°C) yellow, 90 ml, traceable to N.I.S.T
pH Buffer solution 10.00 (25°C) blue, 90 ml, traceable to N.I.S.T
pH Buffer solution 4.00 (25°C) red, 1 ltr., traceable to N.I.S.T
pH Buffer solution 7.00 (25°C) yellow, 1 ltr., traceable to N.I.S.T
pH Buffer solution 10.00 (25°C) blue, 1 ltr., traceable to N.I.S.T

Accessories for conductivity

Conductivity probe
Calibration solution 1413 µS/cm, 500 ml, traceable to N.I.S.T

Accessories for oxygen

Oxygen sensor
Spare membrane for oxygen sensor
Spare electrolyte for oxygen sensor

Accessories

Temperature probe PT1000
RS232 cable
USB cable
Data logger software
Data acquisition software
Power supply
Case incl. foam for SensoDirect 150

«
...
36
37
38
39
40
»

Содержание SensoDirect 150









































Отзывы:

Нет отзывов

Похожие инструкции для SensoDirect 150

Бренд: jenway Страницы: 36

Бренд: Almemo Страницы: 24

Бренд: Circutor Страницы: 72

Бренд: Eaton Страницы: 36

Бренд: Draper Страницы: 8

Бренд: Beijing Huahuan Electronics Страницы: 28

Бренд: Di-LOG Страницы: 32

Бренд: Extech Instruments Страницы: 5

Бренд: Extech Instruments Страницы: 8

Бренд: Keysight Страницы: 119

Бренд: CTC Union Страницы: 26

Бренд: Tenma Страницы: 35

Бренд: UNI-T Страницы: 34

Бренд: Radio Shack Страницы: 24

Beckman Industrial DM78

Бренд: Emerson Страницы: 2

Бренд: Actron Страницы: 2

Бренд: LIMIT Страницы: 36

Бренд: Supco Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды