background image

9

3.2 pH measurement (with ATC , automatic Temperature    
Compensation)

1) All the procedures are the same as for 3.1 “pH measurement  
  (manual temperature setting)“, except for attachment of a  
  temperature probe by inserting the plug of the temperature    
  probe into the “Temp. Socket“ (Page 5, Fig. A-13), and immers- 
  ing the sensing head of the temperature probe into the measure- 
  ment solution.
2) The upper display will show the pH value, the bottom left 
  display will show the Temp. value of the measured solution, and 
  the bottom right display will show “Auto Temp.“ as example below:

When not in use the “Electrode Sensing Head“ (Page 8, Fig. 
B-3) should always be immersed in water by part-filling 
the probe cap, (Page 8, Fig. B-4) and ensuring that the cap 
is firmly lifted onto the probe. Failure to do so will reduce 
probe life. 

3.3 mV Measurement

The instrument has a built in mV (millivolt) measurement function, 
which enables you to make ion-selective, ORP (oxidation reduction 
potential), and other precise mV measurements.
1) Attach the ORP Electrode by installing the “Probe Plug“ of the  
  ORP electrode into the “pH Socket/BNC Socket“ (Page 5, Fig. A-16).
2) Power on the meter by pressing the “Power” button once.
3) Keep pressing the “Mode” button until the display at bottom    
  right shows “PH“ and “Manual Temp.“ indicator.

PH

Auto Temp.

25.0 °C

7.01

Содержание SensoDirect 150









































Отзывы: