Loviband SensoDirect 150 Скачать руководство пользователя страница 30

Страница: 30 / 40

7.5 Auto Power Off Default Setting

• Use “ ” Up, “ ” Down to select “ 1 “ or “ 0 “.

1 = Auto power On.

0 = Auto power Off.

• After Auto Power Off adjustment, push the “Enter” button, then
press “ESC” to save the data and return to the normal display.

7.6 Temp. Unit Default Setting

• Use “ ” Up, “ ” Down to select “1“ or “0“ .

1 = °F
0 = °C

• After adjusting the Temperature unit, push the “Enter” button,
then press “ESC” to save the data and return to the normal
display.

7.7 pH Manual Temp. Setting

•  This procedure is only to adjust the manual temperature
  compensation value for pH measurement.
•  The lower display will show:

M. TEMP. SET
^, v Enter:Y

•  Use “ ” Up, “ ” Down to select the desired manual Temp.
  compensation value.
•  Press “Enter“ once, then press “ESC“ to save the data and

return to the normal display.

7.8 Temp. Compensation Factor Setting

• This procedure is only used for the Conductivity function.
• Use “ ” Up, “ ” Down to select the Temp.

Compensation Factor (% per °C) of the measured solution.

Содержание SensoDirect 150









































Результаты поиска

Содержание SensoDirect 150

Отзывы:

Похожие инструкции для SensoDirect 150

Бренды по названию

Популярные бренды

Loviband SensoDirect 150, Инструкция по эксплуатации

Результаты поиска

Содержание SensoDirect 150

Отзывы:

Похожие инструкции для SensoDirect 150

Бренды по названию

Популярные бренды