Loviband SensoDirect 150 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 40

background image

22

Table of Contents

1.   Specifications .................................................................................. 1
1.1   General Specifications .................................................................... 1
1.2   Electrical Specifications .................................................................. 2
2.   Front Panel Description .................................................................. 5
3.   pH/mV Measuring and Calibration
Procedure ........................................................................................ 7
4.   Conductivity/TDS Measuring and

Calibration Procedure .................................................................. 13

5. DO (Dissolved Oxygen) Measuring

and Calibration Procedure ........................................................... 18

6.   Data Load, Data Record, Data Logger ........................................ 24
7.   Advanced Adjustment Procedure ................................................ 26
7.1   Check Memory Space ................................................................... 27
7.2   Clear Memory ............................................................................... 27
7.3   Date/Time Setting ......................................................................... 27
7.4   Sample Time Setting ..................................................................... 27
7.5   Auto Power Off Default Setting .................................................. 28
7.6   Temp. Unit Default Setting .......................................................... 28
7.7   pH Manual Temp. Value Setting .................................................. 28
7.8   CD Temp. Compensation Factor Setting...................................... 28
7.9   CD ( µS, mS ), TDS ( ppm ) Setting ............................................... 29
7.10  DO % Salt Compensation Value Setting ..................................... 29
7.11  DO Height (Altitude) Compensation Value Setting ................... 30
7.12  Escape from the Setting function ................................................ 30
8.   Data Output .................................................................................. 31
9.   RS232 PC Serial Interface .............................................................. 33
10.   Battery Replacement .................................................................... 35
11.   System Reset ................................................................................. 35
12.   Accessories .................................................................................... 36

«
1
2
3
4
...
»

Содержание SensoDirect 150









































Отзывы:

Нет отзывов

Похожие инструкции для SensoDirect 150

Бренд: Omega Страницы: 17

Бренд: Edison Страницы: 8

Бренд: MW TOOLS Страницы: 29

Бренд: Unitest Страницы: 48

Бренд: PCWork Страницы: 152

Бренд: PCE Health and Fitness Страницы: 13

Бренд: LaserLiner Страницы: 60

Бренд: Performance Tool Страницы: 2

Бренд: gefran Страницы: 7

Бренд: Gossen MetraWatt Страницы: 56

Бренд: Keysight Страницы: 165

Бренд: Keysight Страницы: 177

Бренд: GE Security Страницы: 81

Бренд: YOKOGAWA Страницы: 52

Бренд: IDEAL INDUSTRIES Страницы: 23

Бренд: Multimetrix Страницы: 92

Бренд: Agilent Technologies Страницы: 84

Бренд: Magnum Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды