background image

 

 

  Code: MSGB202$0500.doc                                       18/06/2004                                                                       P.  14 / 20

 

Front panel 

You can display a 'virtual' representation of the front panel of the DMK on the monitor of the PC using the 
remote control software. When you access this window from the 

Display-Front Panel

 menu, the front panel of 

the DMK is shown, with real-time display of the readouts and leds in their current status. Clicking with the 
mouse on the keys, you can select the measurements and functions in the same way as on the physical 
multimeter. However, you cannot access those functions (such as parameter programming, reset counters, 
etc.) that require simultaneous pressing and/or holding down of the keys.  
 

Note: 

The quality of the graphic representation of the front panel may vary according to the graphic resolution of 
your PC and/or the monitor settings used. 
 
 
 

Fig. 7.1 – Display-Front panel 
 

 

 

 

 

 
 
Password 

When the program is started, some of the functions are disabled. You can enter the password that permits 
access to all the functions, in particular those listed below, from the 

Password 

menu: 

 

• 

Modification of the settings of the remote control 

• 

Modification of the password 

• 

Elimination of records from the 

Alarms

 and 

Data collection 

databases 

• 

Access to the page editor  

• 

Modification of the setup parameters of the DMK connected 

 

Fig. 8.1 – Password 

 

 

Name of the 
multimeter 
selected 

Clicking on the 
keys has the 
same effect as 
on the real 
panel 

Real-time 
display of the 
status of the 
readouts and 
leds 

Содержание DMK40





















Отзывы: