Loongson Godson 3A1000 Скачать руководство пользователя страница 43

Страница: 43 / 133

4/29/2020

Godson 3A1000 Processor User Manual

Godson 3A1000 Processor User Manual Part 1

CONF_CTL_26 [63: 0] Offset: 0x1a0 DDR2 667: 0x0000000000000000

ECC_U_DATA [63:32] 63:32

0x0

0x0-0x1fffffff

Record data information when 2bit ECC error occurs (read only)

ECC_U_DATA [31: 0]

31: 0

0x0

0x0-0x1fffffff

Record data information when 2bit ECC error occurs (read only)

CONF_CTL_27 [63: 0] Offset: 0x1b0 DDR2 667: 0x0000000000000000

CKE_DELAY

2: 0

0x0

0x0-0x7

CKE effective delay.

Note: Used to control the response of the internal srefresh_enter command

Time, invalid for Godson No. 3.

CONF_CTL_29 [63: 0] Offset: 0x1d0 DDR2 667: 0x0103070400000101

TDFI_PHY_WRLAT_B

ASE

59:56

0x0

0x0-0xf

Set the delay required to write data in DDR PHY. For the dragon

The value of core 3 should be 2

TDFI_PHY_WRLAT

51:48

0x0

0x0-0xf

Used to display the actual interval from write command to write data issue

Number of cycles (read only)

TDFI_PHY_RDLAT

44:40

0x0

0x0-0xf sets the number of cycles between the read command and the read data return interval

TDFI_CTRLUPD_MIN 35:32

0x4

0x0-0xf Save DFI Tctrlup_min time parameter (read only)

DRAM_CLK_DISABLE 19:16

0x0

0x0-0xf

Set whether to output DRAM clock signal, each bit corresponds to a chip

选

信号。

Choice signal. 0: output clock signal; 1: disable output clock signal

number.

ODT_ALT_EN

8: 8

0x0

0x0-0x1

Whether to support the ODT signal when CAS = 3.

Note: For Godson No. 3, invalid

DRIVE_DQ_DQS

0: 0

0x0

0x0-0x1 Set whether to drive the data bus when the controller is idle

CONF_CTL_30 [63: 0] Offset: 0x1e0 DDR2 667: 0x0c2d0c2d0c2d0205

TDFI_PHYUPD_TYPE

61:48

0x0000 0x0-0x3fff This value is equal to TREF (read only)

TDFI_PHYUPD_RESP 45:32

0x0000 0x0-0x3fff This value is equal to TREF (read only)

TDFI_CTRLUPD_MAX 29:16

0x0000 0x0-0x3fff This value is equal to TREF (read only)

TDFI_RDDATA_EN_B

ASE

12: 8

0x00

0x0-0x1f

Basic time from DDR PHY internal read command to read return

between. For Godson 3 this value is 2

TDFI_RDDATA_EN

4: 0

0x00

0x0-0x1f

Used to display the actual week from when the read command is issued to when the read data is returned

Period

CONF_CTL_31 [63: 0] Offset: 0x1f0 DDR2 667: 0x0020008000000000

DLL_CTRL_REG_0_0 63:32

0x00000 0x0-0xffffffff 0th data group (DQ7-DQ0) DLL control signal

Page 54

Godson 3A1000 Processor User Manual Part 1

24: Control the enable signal of internal DLL, when it is 0, the DLL has

effect

23:16: Control the phase between write data (DQ) and DQS

Relationship, each value is expressed as (1 / precision) * 360. In Godson 3

In the number, this value is generally 1/4, which is 8'h20

7: 0: Control the accuracy of the internal DLL. In Godson 3, this

The value is generally 8'h80

DFT_CTRL_REG

7: 0

0x00

0x0-0xff test enable signal, 0x0 is normal working mode

Содержание Godson 3A1000






































































































































Результаты поиска

Содержание Godson 3A1000

Отзывы:

Похожие инструкции для Godson 3A1000

Бренды по названию

Популярные бренды

Loongson Godson 3A1000, Руководство пользователя

Результаты поиска

Содержание Godson 3A1000

Отзывы:

Похожие инструкции для Godson 3A1000

Бренды по названию

Популярные бренды