Loongson Godson 3A1000 Скачать руководство пользователя страница 92

Страница: 92 / 133

4/29/2020

Godson 3A1000 Processor User Manual

101

Page 114

Godson 3A1000 Processor User Manual Part 1

10: 0 Reserved

REG_50

31: 0 mas_pending_seq

Read and write

Vector of unprocessed request number of master

The corresponding bit can be cleared by writing 1

REG_54

31: 0 mas_split_err

Read and write

split returns the wrong request number vector

REG_58

31:30 Reserved

29:28 tar_split_priority

Read and write

target split returns priority

0 highest, 3 lowest

27:26 mas_req_priority

Read and write

master external priority

0 highest, 3 lowest

25 Priority_en

Read and write

Arbitration algorithm (arbitration between master's access and target's split return)

0: fixed priority

1: rotation

24:18 Reserved

17 mas_retry_aborted

Read and write

master retry cancellation (write 1 to clear)

16 mas_trdy_timeout

Read and write

master TRDY timeout count

15: 8 mas_retry_value

Read and write

00h

master retries

0: unlimited retry

1-255: 1-255 times

7: 0 mas_trdy_count

Read and write

00h

master TRDY timeout counter

0: disabled

1-255: 1-255 beat

Before initiating reading and writing in the configuration space, the application should first configure the PCIMap_Cfg register and tell the

The type of configuration operation and the value on the upper 16-bit address line. Then read the 2K space starting at 0x1fe80000

Write to access the configuration header of the corresponding device. The device number is obtained by coding according to PCIMap_Cfg [15: 0] from low to high priority.

The configuration operation address generation is shown in Figure 10-1.

102

Page 115

Godson 3A1000 Processor User Manual Part 1

Figure 10-1 Configure the read and write bus address generation

Содержание Godson 3A1000






































































































































Результаты поиска

Содержание Godson 3A1000

Отзывы:

Loongson Godson 3A1000, Руководство пользователя, Страница: 92 / 133

Результаты поиска

Содержание Godson 3A1000

Отзывы: