manualshive.com logo in svg

LOGAIRE FIRES MAUI, Инструкция по установке и эксплуатации

Поделиться
Скачать
LOGAIRE FIRES MAUI Скачать руководство пользователя страница 32

P:\Public\Spec Sheets\MAUI Gas Fire Indtructions.pdf 

 

32

MAUI ZERO CLEARANCE 

 

 

ASSEMBLY INSTRUCTIONS 

 

This  zero  clearance  shell  kit  contains  a  base,  a  top  sub-assembly,  a  two  piece  back 

panel, left and right side panels, a zero clearance skirt, (left hand end, right hand end, 

and  main  skirt)  two  flashing  clips,  and  two  skirt  clips.    Assembly  screws  are  also 

included.    Refer  to  diagram  16  on  page  32 during assembly for part placement and 

orientation. 

 

1.  All  assembly  screws  should  be  installed  from  the  outside  of  the  zero  clearance 

shell.  When installing assembly screws, do not over tighten causing screw holes 

to strip out. 

 

2.  Align the two skirt clips (H) with the mounting holes on side sheets (a) and (B).  

Make  sure  that  the  flanges  on  the  skirt  clips  are  to  the  front  of  the  side  sheets.  

Assembly screws may be inserted from the inside on this step. 

 

3.  Locate side panels (A) and (B) inside the flanges of the base (C).  The standoffs 

on the side panels must be located to the outside of the zero clearance shell and 

the  large  holes  in  the  side  panels  must  be  located  towards the base.  Fasten the 

side panels to base, but do not install the back screws at this time. 

 

4.  The back panel consists of a top and bottom piece.  Attach the top back panel (D) 

to  the  rear  side  of  the  bottom  back  panel  (J).    Locate  the  back  panel  assembly 

(D&J) inside the flanges of the base and side panels.  The standoffs on the back 

panel  assembly  must  be  located  to  the  outside  of  the  zero  clearance  shell  and 

aligned with the standoffs on the side panels.  Fasten the back panel to the base 

and sides panels, but do not install the top screws at this time. 

 

5.  Locate the top sub assembly (E) so that the bottom flanges are on outside of the 

back panel and the side panels.  Fasten top sub assembly. 

 

6.  Align the two flashing clips (G) with mounting holes on side3 panels and fasten in 

place. 

 

7.  Assembly left hand skirt and right hand skirt to main skirt.  Align the skirt (I) with 

skirt  clips  mounted  in  the  side  panels.  The  air  holes  in  the  skirt  must  be  down 

towards the base of the zero clearance shell. Centre skirt and fasten in place. 

 

8.  Align the two side support clips (K) with mounting slot on side panels, and start 

the  screws  to  hold  in  place,  but  do  not  completely  tighten.  The  flanges  on  the 

support clips must be towards the front of the zero clearance shell. 

 

 

 

 

Содержание MAUI





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды