Lincoln ZPU 08 Скачать руководство пользователя страница 49

Страница: 49 / 57

Operating Instructions

Pump ZPU 08 ATEX

810-53711-1

Page 49 / 57

Rev.: 003
31/07/2017

SEW motor

Fault

Possible cause

Remedy

Motor does not start

Feed line interrupted

Check and correct connections, if
necessary.

Blown fuse

Replace fuse

Motor circuit breaker has
responded

Check correct adjustment of motor
circuit breaker. If necessary, remedy
the fault

Motor circuit breaker does not
switch; fault in the control program.

Check control program of motor
circuit breaker and, if necessary,
remedy the fault

Motor is hard to start

Motor has been designed for delta
connection, but has been wired to
star connection

Correct the wiring

Voltage or frequency largely differ
from the target value at least when
starting the motor

Provide better grid conditions; check
cross section of the feed line

Motor does not start

when wired as a star connection,

but only when wired as a delta

connection

In case of star connection torque is
not sufficient

Provided the delta starting current is
not too high, immediately switch the
motor on. Otherwise use larger motor
or special version (after consultation)

Contact fault on star respectively
delta connection

Remedy the fault

Wrong direction of motor rotation Motor connected wrongly

Reverse two phases

Motor hums and has

a high power consumption

Defective winding



Consult the manufacturer. Motor

must be sent to the workshop for
repair

Rotor touches

Fuse is tripped

or motor circuit breaker trips

immediately

Short circuit in the line

Remedy the short circuit

Short circuit in the motor



Consult the manufacturer. Motor

must be sent to the workshop for
repair

Lines connected wrongly

Correct the wiring

Short circuit on the motor



Consult the manufacturer. Motor

must be sent to the workshop for
repair

Speed decreasing significantly

in case of load

Overload

Measure performance, if necessary,
use larger motor or reduce load

Voltage drops out

Increase cross section of feed line

For further relevant information on maintenance, see original Instructions by the motor manufacturer. Make
sure to observe these at all times.

Содержание ZPU 08


























































Результаты поиска

Содержание ZPU 08

Отзывы:

Lincoln ZPU 08, Руководство по эксплуатации, Страница: 49 / 57

Результаты поиска

Содержание ZPU 08

Отзывы: