manualshive.com logo in svg

Lincoln ZPU 08, Руководство по эксплуатации, Страница: 44 / 57

Поделиться
Скачать
Lincoln ZPU 08 Скачать руководство пользователя страница 44

 

 Operating Instructions 

   

 

Pump ZPU 08 ATEX 

 

810-53711-1

   

 

 

Page 44 / 57

 

Rev.: 003 
31/07/2017 

 
 

10.  Maintenance 

 

Regular and appropriate maintenance is a prerequisite to detect and clear faults in 
time. As individual operating conditions cannot be defined for all applications, the 
listed terms represent a general advice for undisturbed operation. The terms have 
to be adapted to the local conditions always.  

 

 

 

DANGER

 

Risk of explosion 

When carrying out maintenance, repair or modification works on 
explosion-protected machines, observe the legal and operational 
prescriptions. If the works are not carried out by the 
manufacturer, authorized and qualified personnel only is allowed 
to carry out such works. Works then have to be reviewed by a 
qualified and officially recognised person. 
Carry out work on electrical parts only, if the atmosphere is not 
potentially explosive. 

Electric shock 
Make sure to disconnect the pump from the power supply before 
carrying out works on electrical parts.

 

 

10.1. 

Maintenance of pump 

Any maintenance works may be carried out only while the pump is idle and when 
there is no potentially explosive atmosphere. 
The pump is mainly maintenance-free.  
However, the following parts should be inspected and, if necessary, replaced by 
new parts at regular intervals: 

 

Pressure relief valves 

 

Check valves 

 

Lubricant filter 

 
Tolerance frequency of the pressure control valve ± 10 % 
If this tolerance is exceeded, the pressure control valve must be replaced. 

 

 

Содержание ZPU 08


























































Отзывы:

Нет отзывов