Lincoln ZPU 08 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 57

Lincoln ZPU 08 Скачать руководство пользователя страница 27

Operating Instructions

Pump ZPU 08 ATEX

810-53711-1

Page 27 / 57

Rev.: 003
31/07/2017

3.3.

Specification

Lubricants of the following consistencies can in principle be conveyed using SKF
centralized lubrication systems.



Lubricating greases up to NLGI 2



solids content up to 5 % maximum



mineral oils with a viscosity of minimum 40 mm²/s at +40 °C

Lubricants must be compatible with the following materials:



steel / grey iron / brass / copper / aluminium



NBR / FPM / ABS / PA / PU

NOTICE

Risk of damage to the machine or system
Do not mix lubricants. This may have unforeseeable effects on the usability and
therefore on the function of the centralized lubrication system.
Due to the multitude of possible additives, it is possible that individual lubricants,
which  -  according  to  the  manufacturer's  data  sheets  -  fulfil  the  necessary
specification, are not in fact suitable for use in centralized lubrication systems (e.g.
incompatibility between synthetic lubricants and materials). In order to avoid this,
always use lubricants tested by SKF.
Please contact the SKF Service Department for an overview of lubricants tested
by SKF.

DANGER

Risk of explosion
The ignition temperature of the lubricant must lie at least 50 K over
the maximum admissible surface temperature of the components.

«
...
25
26
27
28
29
...
»

Содержание ZPU 08


























































Отзывы:

Нет отзывов