Lincoln ZPU 08 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 57

Lincoln ZPU 08 Скачать руководство пользователя страница 40

Operating Instructions

Pump ZPU 08 ATEX

810-53711-1

Page 40 / 57

Rev.: 003
31/07/2017

8.

Installation and commissioning

8.1.

Filling of the reservoir

NOTICE

Risk of centralized lubrication system faults

When filling ensure that no dirt enters the reservoir.

Filling via filling adapter

Automatic Filling:
The filler pump is started by the low-level
indication and stopped by the high-level
indication.

Manual filling:

Filling procedure must be supervised by a
second person.



Switch the filling pump on.



Fill the reservoir



Switch off the filler pump.

Filling port (C)

Filling via the reservoir lid



Switch the pump off.



Open the reservoir lid (1.1).



Ensure that no dirt enters the reservoir

or the inner side of the reservoir lid. In
case of reservoirs equipped with a
sensor, the sensor must not be
damaged or contaminated.



Fill in lubricant up to a maximum of

1 cm below the reservoir rim.



Reposition and close the reservoir lid

(1.1). Make sure not to crush the
grounding cable.



Switch the pump on.

C

1.1

«
...
38
39
40
41
42
...
»

Содержание ZPU 08


























































Отзывы:

Нет отзывов