Subject to modifications
Owner Manual
Technical Description
2.1A-30001-H07
LINCOLN GmbH • Postfach 1263 • D-69183 Walldorf • Tel +49 (6227) 33-0 • Fax +49 (6227) 33-259
Page 23 of 36
Technical Data
Pump
Admissible operating temperature ..............-25° C to 70° C
1)
Number of outlets.......................................................1,2 or 3
Reservoir capacity ................................................. 2 l, 4 l, 8 l
Refilling ................. via hydraulic lubrication fitting or from top
Lubricant ....................................greases up to NLGI grade 2
&
mineral oils of at least 40mm²/s (cST) at 40° C
Class of protection ................. IP6K 9K acc. to DIN 40050 T9
6001a02
1)
NOTE
The pump is designed for the above
mentioned temperature range. The lu-
bricants used must still be pumpable at
the temperatures mentioned above. In
case of doubt, consult the lubricant
manufacturer.
NOTE
The pump reservoirs are factory-primed with lubrication
grease Renocal FN745 and EP additives make Fuchs. This
composition is compatible to most of the commercial greases
and helps to prevent faults. If requested by the customer, the
pumps can either be primed with another type of lubrication
grease or be supplied without priming.
Motor
DC gear motor (interference-suppressed)
-
Operating voltage. ................................12VDC or 24VDC
- Max.
current
input
12V .......................................................................... 6.5 A
24V ............................................................................. 3 A
Speed ............................................................ approx.17 rpm
Noise emission .................................................... < 70 dB(A)
Pump element with fixed lubricant output
Piston diameter, K5.......................................................5 mm
-
Lubricant output................................... approx. 2 cm³/min
Piston diameter, (standard) K6 .....................................6 mm
- Lubricant
output................................. approx.
2.8cm³/min
Piston diameter, K7, C7, S7
3)
.......................................7 mm
-
Lubricant output................................... approx. 4 cm³/min
Max. operating pressure. ...........................................350 bar
Connection thread......................................................... G 1/4
-
suitable for tube DIA................................................6 mm
2)
suitable for chisel paste; contact the manufacturer of the lubrication
system
3)
suitable for lubricants containing silicone
Pump element with adjustable lubricant output
KR
............................................... 0.04 to 0.18 cm³/stroke
.......................................................... 0.7 to 3 cm³/min
Connection thread.................................................... G 1/4 in.
-
suitable for tube DIA................................................6 mm
-
suitable for tube DIA................................................8 mm
6001a02
IMPORTANT
The lubricant output listed refers to
grease of NLGI grade 2 measured at
20°C, backpressure 100 bar, nominal
voltage 12/24 V. Any differing pressures
or temperatures result in different lubri-
cant outputs. Any system design must be
based on the above values.compte.
Pressure relief valve
SVETVT-350-G 1/4A-D6 ................................... 624-28894-1
SVETVT-350-G 1/4A-D8 ................................... 624-28774-1
Torsion torques
Install pump .................................................................18 Nm
Electric motor on housing ............................................12 Nm
Pump element in housing ............................................20 Nm
Closure plug in housing ...............................................12 Nm
Return line connector in housing ..........................10 - 12 Nm
Weights
The weights below include the following ‘‘
individual
weights”:
- Pump kit with
one
pump element, pressure relief valve,
grease filling (0.75 kg, 1.5 kg)
- Packing (cardboard box)
- Attaching parts
- Operating Instructions
2 l reservoir, standard design (0.75 kg)
-
Pump 203 without connection cable .......................5.4 kg
-
Pump 203, version E 1............................................6.5 kg
-
Pump 203, version E 2............................................7.1 kg
4 l reservoir, standard design (1.5 kg)
-
Pump 203 without connection cable .......................8.3 kg
-
Pump 203, version E 1............................................9.3 kg
-
Pump 203, version E 2............................................9.9 kg
8 l reservoir, standard design (1.5 kg)
-
Pump 203 without connection cable .......................8.6 kg
-
Pump 203, version 1A1...........................................9.6 kg
-
Pump 203, version 2A1.........................................10.2 kg
In the case of pump versions deviating from those mentioned,
add the weights of the following components to the mentioned
weights:
- Per pump element................................................ +0.2 kg
-
Per pressure relief valve ...................................... +0.1 kg
-
10 m monitoring cable, 5-wire
(microprocessor) E 4............................................ +1.1 kg
-
10 m monitoring cable, 4-wire
(microprocessor) E 4............................................ +0.4 kg
-
Connection cable with piston detector ....................0.1 kg
-
Reservoir version ”Filling from top” (only 2 l)
3)
...
+0.15 kg
-
2 l flat-type reservoir ............................................ +0.5 kg
6001a02
3)
NOTE
The 4l and 8l reservoirs have the standard
design ”filling from top”.