Lika DSP417 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 28

background image

SMAL CANlift

MAN SMAL I6 E 1.3.doc

Pag.16

www.lika.it

www.lika.biz

1906

PDO1 parameters

PDO1 is used by default for cyclic transmission of the position value.
See object 1906h sub 5 for setting of cyclic timer.

•

01

COB;ID of PDO1 [Unsigned32, rw]

Default = 0000 018Ch

•

02

Transmission type [Unsigned8, rw]

Default = FFh (cyclic transmission)

•

03

Inhibit time [Unsigned8, rw]

Default = 00h

•

04

Reserved

•

05

Event Timer

Default = 00h (disabled)

ATTENTION:

The COB;ID of PDO1 for CANlift devices follows the lift number and the car
position unit. If more devices are connected to the network with the same lift
number, be sure to set different COB;ID of PDO1 for each device.

NOTE:

•

The transmission of PDO1 can be enabled (or disabled) setting to “0” (or “1”)
the most significant bit (MSB) used by PDO (object 1906h, sub1).
0000 018Ch: PDO1 enable
8000 018Ch: PDO1 disabled.

•

Cyclic transmission or synchronous transmission can be modified setting the
object 1906h sub 2:
01h: synchronous transmission each SYNC;
02h: synchronous transmission after 2 SYNC;
…
FEh: cyclic transmission (see object 3007h for cyclic timer)
FFh: cyclic transmission (see object 1906h sub 5 for cyclic timer)

1B0601

PDO1 mapping parameter [Unsig32, rw]

This object contains the mapped position value of the encoder according to the
DSP417 device profile.
Default = 6383 0120h

«
...
14
15
16
17
18
...
»

Содержание DSP417





























Отзывы:

Нет отзывов

Похожие инструкции для DSP417

Бренд: Campbell Страницы: 25

Бренд: Larson Davis Страницы: 2

Бренд: G-Tek Страницы: 27

Бренд: HANYOUNG NUX Страницы: 4

Бренд: jenway Страницы: 30

Бренд: National Meter & Automation Страницы: 24

Бренд: Lakeshore Страницы: 2

Бренд: Kamstrup Страницы: 4

Бренд: OHAUS Страницы: 32

Бренд: velocomp Страницы: 4

Бренд: Keithley Страницы: 31

Бренд: Keithley Страницы: 63

Бренд: Keithley Страницы: 18

Бренд: Keithley Страницы: 73

Бренд: Sensia Страницы: 139

Бренд: York Страницы: 2

Бренд: Fluke Biomedical Страницы: 28

Бренд: VOLTCRAFT Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды